User manual SONY HDWD2000

[. . . ] HD DIGITAL VIDEOCASSETTE RECORDER HDW-D2000 OPERATION MANUAL 1st Edition (Revised 1) [English] WARNING To prevent fire or shock hazard, do not expose the unit to rain or moisture. To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only. THIS APPARATUS MUST BE EARTHED. This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. [. . . ] To insert characters Press the F3 (T) or F4 (t) button until the character place after the place where you want to insert starts flashing, and then press the F6 (INSERT) button. Chapter 7 Tele-File 8 Press the F2 (OK) button. The comment is confirmed and the unit returns to clip data display mode. 7-10 Chapter 7 Tele-File 7-3-5 Displaying and Modifying Attribute Data You can display and modify attribute data. The example below shows attribute data displayed on the monitor. Video final recording date Administrator data Number of cue points TELE-FILE INFORMATION *REC DATE 2001/07/21 TITLE TEST 01 ID ADMIN MODEL SERIAL 00000 WRITE INHIBIT OFF THREAD COUNT 00012 CUE POINT No. 0003 CONTROL MODE panel SIZE 01024 USED 0270 Memory size Amount of memory used Video final recording date The most recent date (year/month/day) on which video was recorded on the tape. Title The title (name assigned to Tele-File, etc. , maximum 24 characters). ID The ID (unique number assigned to Tele-File, maximum 20 digits). Administrator data Data about the administrator of the cassette or tape material (maximum 16 characters). Model name The model name of the VTR that recorded most recently to the tape. Serial number The serial number of the VTR that recorded most recently to the tape. Write inhibit setting Whether the entire Tele-File is write inhibited. The write inhibit setting can be modified. Thread count The thread count value recorded on the tape. Number of cue points The number of cue points recorded in the Tele-File. You can check the cue point values in clip data display mode. Control mode The setting of menu item 133. For more information about menu item 133, see page 10-12. Chapter 7 Tele-File Memory size The size of the memory in the Tele-File (unit: bytes). Amount of memory used The amount of memory currently being used (unit: bytes). Chapter 7 Tele-File 7-11 7-3 Tele-File Menu To modify attribute data You can modify the title, ID, administrator data, and write inhibit setting attributes. However, the attributes cannot be modified when the control mode is "remote. " The modification is not possible when the write inhibit setting is ON, either. Proceed as follows after setting the write inhibit setting to OFF. To format the Tele-File memory You can format the Tele-File memory (erase all modifiable data). However, the memory cannot be formatted in the following cases. · When the write inhibit setting is ON · When the control mode is "remote" To format Tele-File memory, proceed as follows. 1 Rotate the MULTI CONTROL knob to select the item. The F2 (SELECT) button is enabled when you select an item that can be modified (title, ID, administrator data, and write inhibit setting). 1 2 Press the F4 (FORMAT) button. All modifiable data is erased. 2 3 4 Press the F2 (SELECT) button. Note The data can be set or modified. Rotate the MULTI CONTROL knob to set or modify the data. [. . . ] ±50 times normal playback speed (59. 94i, 29. 97PsF) Still to approx. ±58 times normal playback speed (50i, 25PsF) Still to approx. ±60 times normal playback speed (24PsF, 23. 98PsF) Digital Betacam playback: Still to approx. ±50 times normal playback speed MPEG IMX playback: Still to approx. [. . . ]