User manual SONY HDWS2000

[. . . ] HD DIGITAL VIDEOCASSETTE RECORDER HDW-S2000 HDW-S2000P OPERATION MANUAL 1st Edition (Revised 1) [English] WARNING To prevent fire or shock hazard, do not expose the unit to rain or moisture. To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only. THIS APPARATUS MUST BE EARTHED. This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. AVERTISSEMENT Afin d'éviter tout risque d'incendie ou d'électrocution, ne pas exposer cet appareil à la pluie ou à l'humidité. [. . . ] Serial number The serial number of the VTR that recorded most recently to the tape. Write inhibit setting Whether the entire Tele-File is write inhibited. The write inhibit setting can be modified. Thread count The thread count value recorded on the tape. Number of cue points The number of cue points recorded in the Tele-File. You can check the cue point values in clip data display mode. Control mode The setting of menu item 133. For more information about menu item 133, see page 10-12. Chapter 7 Tele-File Memory size The size of the memory in the Tele-File (unit: bytes). Amount of memory used The amount of memory currently being used (unit: bytes). Chapter 7 Tele-File 7-11 7-3 Tele-File Menu To modify attribute data You can modify the title, ID, administrator data, and write inhibit setting attributes. However, the attributes cannot be modified when the control mode is "remote. " The modification is not possible when the write inhibit setting is ON, either. Proceed as follows after setting the write inhibit setting to OFF. To format the Tele-File memory You can format the Tele-File memory (erase all modifiable data). However, the memory cannot be formatted in the following cases. · When the write inhibit setting is ON · When the control mode is "remote" To format Tele-File memory, proceed as follows. 1 Rotate the MULTI CONTROL knob to select the item. The F2 (SELECT) button is enabled when you select an item that can be modified (title, ID, administrator data, and write inhibit setting). 1 2 Press the F4 (FORMAT) button. All modifiable data is erased. 2 3 4 Press the F2 (SELECT) button. Note The data can be set or modified. Rotate the MULTI CONTROL knob to set or modify the data. The change to the setting is confirmed. Note Chapter 7 Tele-File In the following cases, the FORMAT item does not appear, and it is not possible to select a data modification mode. · When setup menu item 133 is set to REMOTE · When the memory label itself is write protected In the following cases, the SELECT item does not appear, and it is not possible to select a data modification mode. · When setup menu item 133 is set to REMOTE · When the memory label itself is write protected 7-12 Chapter 7 Tele-File Chapter 8 UMID Functions 8-1 Overview of UMID Functions A UMID with a Basic section only is called a Basic UMID. A UMID with both Basic and Source Pack sections is called an Extended UMID. The following figure shows a general overview of the information contained in a UMID. The UMID (Unique Material Identifier) is a type of meta-data in video and audio materials. It has been internationally standardized in SMPTE Standard 330M. This unit supports recording and generation of UMIDs. The UMID is made up of a section called the "Basic" section and a section called the "Source Pack" section. [. . . ] 1-782-165-11 Plug holder 3-613-640-01 · For customers in European countries other than the United Kingdom Part No. 1-782-164-11 Plug holder 3-613-640-01 Design and specifications are subject to change without notice. Appendix A-5 Specifications Relation between HKDV-900/503 setting items and setup menu of this unit HKDV-900/503 setting items Setup menu items of this unit HD Master HD Y HD Pb HD Pr HD Setup HD Sync Phase HD Fine D1 Master D1 Y D1 B-Y D1 R-Y D2 VIDEO D2 CHROMA D2 HUE SETUP SD Sync Phase SD Fine CROSS COLOR H CROP POSITION DETAIL GAIN LIMITTER CRISP DEPEND FREQUENCY H/V RATIO GAMMA CROP LETTER BOX SQUEEZE Appendix 740: MASTER LEVEL (HD) a) 741: Y LEVEL (HD) a) 742: Pb LEVEL (HD) a) 743: Pr LEVEL (HD) a) 745: SETUP LEVEL (HD) a) 746: SYNC PHASE (HD/UC) a) 747: FINE (HD/UC) a) No corresponding menu item No corresponding menu item No corresponding menu item No corresponding menu item 715: VIDEO GAIN CONTROL (HD/DC/SD/UC) a) 716: CHROMA GAIN CONTROL (HD/DC/SD/UC) a) 717: CHROMA PHASE CONTROL (HD/DC/SD/UC) a) 713: VIDEO SETUP REFERENCE LEVEL: OUTPUT LEVEL (DC/SD) a), c) 718: SETUP LEVEL/BLACK LEVEL (HD/DC/SD/UC) a), c) 719: SYSTEM PHASE SYNC (DC/SD) 720: SYSTEM PHASE SC (DC/SD) 934: CROSS COLOR (DC) 932: H CROP POSITION (DC)/951: H CROP POSITION (UC) b) 935: DETAIL GAIN (DC)/954: DETAIL GAIN (UC) b) 936: LIMITER (DC)/955: LIMITER (UC) b) 937: CRISP THRESHOLD (DC)/956: CRISP THRESHOLD (UC) b) 938: LEVEL DEPEND THRESHOLD (DC)/957: LEVEL DEPEND THRESHOLD (UC) b) 939: H DETAIL FREQUENCY (DC)/958: H DETAIL FREQUENCY (UC) b) 940: H/V RATIO (DC)/959: H/V RATIO (UC) b) 941: GAMMA LEVEL (DC)/960: GAMMA LEVEL (UC) b) 930: DOWN CONVERTER MODE/950: UP CONVERTER MODE b) 930: DOWN CONVERTER MODE/950: UP CONVERTER MODE b) 930: DOWN CONVERTER MODE/950: UP CONVERTER MODE b) a) Valid for output only when F1 (V. PROC) in function menu page 2 is set to MENU. b) Select whether to set DC or UC with menu item 212 (VIDEO REMOTE CONTROL SELECT). When both are selected (menu item 1c, is U&D), both of the corresponding menu settings are made, but this unit's answer values and unity values are the DC values. [. . . ]