User manual SONY HVR-M10U

[. . . ] 2-549-780-11(1) Digital HD Videocassette Recorder Operating Instructions HVR-M10U/M10N/M10E/M10P 2005 Sony Corporation WARNING To prevent fire or shock hazard, do not expose the unit to rain or moisture. To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only. Owner's record The model number is located at the front of the unit and the serial number on the left. [. . . ] NDF: Selects the non-drop frame mode. Note When you set [50i/60i SEL] on the [OTHERS] menu to 50i, this unit uses the 50i system specification. Therefore, the time code generated by the unit during recording in the DVCAM format is that of the nondrop frame mode. Even if a 60i system signal is input to the HDV/DV jack, the time code generated by the unit is the non-drop frame mode regardless of the [TC FORMAT] setting. If you intend to set the unit to generate the time code in the drop frame mode, set [50i/60i SEL] to 60i. 42 Chapter 3 Dubbing/Editing Audio Dubbing You can record just sound on a recorded tape. (Audio dubbing) Notes · You can dub the sound onto a DVCAM-formatted tape (recorded) in the 32 kHz audio mode (4-channel/ 12 bits). You cannot dub sound recorded in 48 kHz (2-channel/16 bits) audio mode on a tape or a tape recorded in nonstandard audio. · If the audio mode of the recorded tape is 32 kHz, you can dub the sound regardless of the [AUDIO MODE] setting on the [AUDIO SET] menu. 47) · The sound is dubbed only onto channels 3/4. You cannot dub the sound onto either of them or channels 1/2. Connection of external devices The following shows an example of a basic connection for audio dubbing. Headphones This unit (front panel) Chapter 3 Dubbing/Editing Audio output Sound source AUDIO IN PHONES AUDIO OUT Analog video output Audio input Video input : Signal flow Chapter 3 Dubbing/Editing 43 Audio Dubbing Dubbing sound To stop audio dubbing Press the STOP button. To output the sound you want Select the sound to be output from the AUDIO jack or headphone jack. Set the [AUDIO MIX] on the [AUDIO SET] menu as follows: CH1, CH2: Outputs the sound recorded on channels 1/2 on the tape. MIX: Outputs the synthesized sound of channels 1/3 and channels 2/4. CH3, CH4: Outputs the sound recorded on channels 3/4 on the tape. The indicator of the audio level meters will display according to the above-settings. Notes 1 2 3 4 5 Chapter 3 Dubbing/Editing Connect the unit and the sound source using a phono jack cable (not supplied). Set the INPUT SELECT switch to S VIDEO or VIDEO. Play back the tape inserted in this unit. At the point you want to start dubbing, press the PAUSE button to turn the unit to the playback pause mode. While holding the AUDIO DUB button down, press the PLAY button to turn the unit to the audio dubbing pause mode. X lights on the screen. 6 Select the recording level adjustment mode using the AUTO/MANU (manual) audio switch. If the MANU mode is selected, set [AUDIO LIMIT] of the [AUDIO SET] menu (p. 47). 7 Adjust the recording level by turning the AUDIO REC LEVEL control knobs. You can adjust the recording level with the AUDIO REC LEVEL control knobs if you have selected MANU in step 6. [. . . ] 47 AUDIO MIX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 AUDIO MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 AUDIO MONI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 T TC FORMAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]