User manual SONY HVR-Z5U SERVICE MANUAL

[. . . ] HVR-Z5C/Z5E/Z5J/Z5N/Z5P/Z5U RMT-831 SERVICE MANUAL Ver. 1. 2 2009. 04 Revision History US Model Canadian Model AEP Model E Model Chinese Model Japanese Model Revised-1 Replace the previously issued SERVICE MANUAL 9-852-623-12 with this Manual. N MECHANISM (MDX-N221) Photo: HVR-Z5J Link SPECIFICATIONS MODEL INFORMATION TABLE SERVICE NOTE DISASSEMBLY BLOCK DIAGRAMS FRAME SCHEMATIC DIAGRAMS SCHEMATIC DIAGRAMS PRINTED WIRING BOARDS REPAIR PARTS LIST ADJUSTMENTS INSTRUCTION MANUAL The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Les composants identifis par une marque 0 sont critiques pour la scurit. Ne les remplacer que par une pice portant le numro spcifi. DIGITAL HD VIDEO CAMERA RECORDER HVR-Z5C/Z5E/Z5J/Z5N/Z5P/Z5U 9-852-623-13 2009D0800-1 2009. 04 Published by Kohda TEC Sony EMCS Co. These specifications are extracted from instruction manual of HVR-Z5C/Z5E/Z5P. ENGLISH JAPANESE SPECIFICATIONS System Video recording system (HDV) 2 rotary heads, Helical scanning system Video recording system (DVCAM (DV)) 2 rotary heads, Helical scanning system Still image recording system Exif Ver. [. . . ] Also confirm that the RF waveform amplitude at entrance side (B) and exit side (C) is 50% or more respectively, when taking the amplitude (A) in the CUE or REV mode as 100%. Confirm that the pitches between the peaks of the RF waveform are equally spaced. Also confirm that the RF waveform amplitude at entrance side (B) and exit side (C) is 50% or more respectively. A=100% B C A=100% 400 sec FWD mode B = 50% or more C = 50% or more E max E min Fig. Rise-up Check 1) Play back the tracking standard (XH2-1A1) (Ref. 2) Change the modes from CUE mode to FWD. Confirm that the RF waveform rises up within two seconds when the mode is changed from CUE mode to FWD. 3) Change the modes from REV mode (two seconds or more of REV and to the FWD within five seconds) to FWD. Confirm that the RF waveform rises up within two seconds when the mode is changed from REV mode to FWD. 4) Change the modes from STOP mode to FWD. Confirm that the RF waveform rises up within two seconds when the mode is changed from STOP mode to FWD. E min: Minimum amplitude E max: Maximum amplitude (E max E min) 30% or ( 3 A) 10 Fig. 6-2-16 4) Confirm that the RF waveform does not have excessive fluctuation of amplitude. (Fluctuation of amplitude should be 10% or less at both entrance side (B) and exit side (C), when taking the amplitude (A) in the CUE or REV mode as 100%) FWD mode B 10% C 10% Fig. 6-2-17 HVR-Z5C/Z5E/Z5J/Z5N/Z5P/Z5U 6-96 6-3. Adjusting Connectors The measuring point of the playback RF signal is CN1004 of VC543 board. Connect the measuring instruments via the CPC-13 jig (J-6082-443-A). Refer to "MECHANISM SECTION ADJUSTMENT" for the measuring method. The following table lists the test pin numbers of CPC-13 jig, and the pin numbers and signal names of CN1004. 1 (20) 2 (19) 3 (18) 4 (17) 5 (16) 6 (15) 7 (14) 8 (13) 9 (12) 10 (11) Signal Name REG_GND RF_MON REG_GND SWP FRRV REG_GND GND GND EEP_SI_C EEP_SI_S Pin No. 11 (10) 12 (9) 13 (8) 14 (7) 15 (6) 16 (5) 17 (4) 18 (3) 19 (2) 20 (1) Signal Name EEP_SO_C EEP_SO_S EEP_SCK_C EEP_SCK_S D_2. 8V MD2_C MD2 XCS_MC_FLASH_C XCS_MC_FLASH XSYS_RST 3-1-1. Precautions on Adjusting Note: Before performing the adjustment, check the data of page: 0, address: 10 is "00". If not, select page: 0, address: 00, and set data "00". 1) The adjustments of this unit are performed in the VTR mode (VCR mode) or camera mode (CAMERA mode). 3-1-3. [. . . ] : Points deleted portion & : Points added portion After change JK-376 BOARD Ref. Description < CAPACITOR > C9501 C9502 1-164-935-11 CERAMIC CHIP 1-164-935-11 CERAMIC CHIP 470PF 470PF 10% 10% 50V 50V Before change 5-21 ) PI-029 BOARD Ref. Description < BATTERY HOLDER > 0*BH7001 1-756-615-51 HOLDER, BATTERY (Note) 0BH7001 PI-029 BOARD Ref. Description < BATTERY HOLDER > 1-756-615-61 HOLDER, BATTERY (Note) 5-25 $ VC-543 BOARD Ref. [. . . ]