User manual SONY ICF-CD543RMSIL

[. . . ] 3-238-576-21 (1) WARNING To prevent fire or shock hazard, do not expose the unit to rain or moisture. Precautions · Operate the unit on the power source specified in the "Specifications. " · To disconnect the power cord (mains lead), pull it out by the plug, not the cord. · Do not leave the unit in a location near a heat source such as a radiator or airduct, or in a place subject to direct sunlight, excessive dust, mechanical vibration, or shock. · Allow adequate air circulation to prevent internal heat build-up. Do not place the unit on a surface (a rug, a blanket, etc. ) or near materials (a curtain) which might block the ventilation holes. [. . . ] Never spill liquid of any kind on the appliance. Cleaning Unplug the appliance from the wall outlet before cleaning or polishing it. Do not use liquid cleaners or aerosol cleaners. Use a cloth lightly dampened with water for cleaning the exterior of the appliance. Clean the appliance only as recommended by Sony. Attachments Do not use attachments not recommended by Sony, as they may cause hazards. Specifications AUDIO POWER SPECIFICATIONS POWER OUTPUT AND TOTAL HARMONIC DISTORTION With 3. 2­ohm loads, both channels driven from 100 ­ 10 000 Hz; rated 1. 4 W per channelminimum RMS power, with no more than 10 % total harmonic distortion in AC operation. ANTENNAS Outdoor Antenna Grounding If an outdoor antenna or cable system is installed, follow the precautions below. An outdoor antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can come in contact with such power lines or circuits. WHEN INSTALLING AN OUTDOOR ANTENNA SYSTEM, EXTREME CARE SHOULD BE TAKEN TO KEEP FROM CONTACTING SUCH POWER LINES OR CIRCUITS AS CONTACT WITH THEM IS ALMOST INVARIABLY FATAL. Be sure the antenna system is grounded so as to provide some protection against voltage surges and built-up static charges. Section 810 of the National Electrical Code provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. CD player section System: Compact disc digital audio system Laser diode properties: Material: GaAlAs Wavelength: 780 nm Emission duration: Continuous Laser output: Less than 44. 6 µW (This output is the value measured at a distance of about 200 mm from the objective lens surface on the optical pick-up block with 7 mm aperture. ) +1 Frequency response: 20 ­ 20 000 Hz ­1. 5 dB Wow and flutter: Below measurable limit Antenna Grounding According to the National Electrical Code Antenna Lead-in Wire Ground Clamps Electric Service Equipment NEC-NATIONAL ELECTRICAL CODE Antenna Discharge Unit (NEC Section 810-20) Grounding Conductors (NEC Section 810-20) Ground Clamps Power Service Grounding Electrode System (NEC Art 250 Part H) Y ANT ARR o) W TED udi LIMI rtable A Po ( Radio section SERVICE Damage Requiring Service Before You Begin Thank you for choosing the Sony CD kitchen clock radio!It will give you many hours of reliable service and listening pleasure. Before operating the unit, please read these instructions thoroughly and retain them for future reference. Frequency range: TV: 2 ­ 13 ch WEATHER: 1 ­ 7 ch FM: 87. 5 ­ 108 MHz AM: 530 ­ 1 710 kHz General Time display: 12-hour system Speaker: 77 mm (3 1/8 inches) dia, 3. 2 Power outputs: 2 W + 2 W (at 10% harmonic distortion) Power requirements: 120 V AC, 60 Hz Dimensions: Approx. 350 × 88 × 310 mm (w/h/d) (Approx. 13 7/8 × 3 1/2 × 12 1/4 inches) incl. projecting parts and controls Mass: Approx. Magnet "RADIO" appears in the display. The display shows the band and frequency for a few seconds and then changes back to the current time. Operating the Cooking Timer (Countdown Timer) The timer can be set at one minute intervals between 1­120. 1 2 Press RADIO ON/BAND repeatedly to select the desired band. Each press changes the band as follows: AM FM1 FM2 TV Turn TIMER until the desired time appears in the display. "TIMER" will appear in the display when TIMER is turned. After setting the time, the current time is displayed again if you do not perform any operation for more than 60 seconds. WEATHER 2 Push TIMER once. Timer indicator lights and beep sounds. While the timer is set, the display shows the remaining time. When using FM1 or FM2 preset mode, you may listen to the radio on either mode (See "Presetting Your Favorite Station"). 3 The VOL + and u buttons have a tactile dot. Size AAA (R03) x 2 Use TUNE/TRACK·TIME SET + or ­ to tune in to the desired station. Two short beeps sound when the minimum frequency of each band is received during tuning. To display the current time, press CLOCK. Cooking Timer ON-- When the time has elapsed, the buzzer will sound and the TIMER indicator flashes. Even if the CD or the radio is being played, the buzzer of the timer sounds together. While the buzzer sounds, the volume of the CD or the radio is decreased. The volume returns to the previous volume level when the buzzer stops. 4 1 Press Z OPEN/CLOSE and place a CD on the disc tray. Adjust volume using VOLUME + or ­. TIMER Turn MEGA BASS LOW OFF HIGH Installing the Unit Under a Cabinet (See Fig. A) The unit can be installed without the spacer. To check the station being received Press RADIO ON/BAND lightly. [. . . ] The new station will replace the previous station on the PRESET TUNING button. Press CLOCK for a few seconds. You will hear a beep and the hour will start to flash in the display. Incorrect 3 4 Press TUNE/TRACK·TIME SET + or ­ until the correct hour appears in the display. Press CLOCK once. The minute will flash. Tuning in to a Preset Station 1 Press RADIO ON/BAND to turn on the Do not touch the surface. Do not stick paper or tape nor write anything on the surface. 2 3 4 radio. Adjust the volume using VOLUME + or ­. After a few seconds, the display returns to the current time but the PRESET TUNING button number remains. Select the PRESET preset number Each press of PRESET, you can select the preset number (1­5). [. . . ]