User manual SONY ICF-CS10IP

[. . . ] 4-150-697-11(1) Owner's Record WARNING The model number and the serial number are located on the bottom. Record the serial number in the space provided below. Refer to them whenever you call upon your Sony dealer regarding this product. ________________________________ For customers who purchased this product in the USA Please register this product on line at http://www. sony. com/productregistration. [. . . ] If you use a device that does not match the connector, connect it to the AUDIO IN terminal of this unit with the supplied audio connecting cable. Sony cannot accept responsibility in the event that data recorded on an iPod is lost or damaged when using an iPod connected to this unit. For details of environmental conditions for operating your iPod, check the website of Apple Inc. iPod is a trademark of Apple Inc. , registered in the U. S. All other trademarks and registered trademarks are of their respective holders. In this manual, TM and ® marks are not specified. "Made for iPod" means that an electronic accessory has been designed to connect specifically to iPod and has been certified by the developer to meet Apple performance standards. "Works with iPhone" means that an electronic accessory has been designed to connect specifically to iPhone and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards. 7 If "A" or "B" does not appear in the The radio will turn on at the set time. display, press ALARM SET A or B again. Setting the sleep timer You can fall asleep to music, etc. , using the builtin sleep timer that turns off the unit automatically after a preset duration. Setting the Buzzer Alarm 1 Perform steps 1 to 8 in "To set the alarm. " 2 Press ALARM SET A or B to select "BUZZER" alarm mode. The setting is entered. 1 Press SLEEP while the unit is turned on. 2 Press SLEEP to set the sleep timer duration. "SLEEP" appears and the sleep time flashes in the display. 3 If "A" or "B" does not appear in the The buzzer will sound at the set time. Note The volume cannot be set for the buzzer alarm. display, press ALARM SET A or B again. Each time you press SLEEP, the duration (in minutes) changes as follows: 90 60 OFF 30 15 To confirm an alarm time setting 1 Attach the adapter for your iPod/iPhone. 2 Insert your iPod/iPhone into the connector of the unit. Setting the alarm This clock radio is equipped with 3 alarm modes--iPod, radio and buzzer. Before setting the alarm, make sure to set the clock (see "Setting the clock for the first time"). Press TIME SET + or ­. The setting will be displayed for about 4 seconds. To change an alarm setting The display returns to clock mode for about 4 seconds after you have finished the duration setting and released SLEEP, and then the sleep timer starts. The unit will play for the duration you set, and then shut off. AC power cord Tuning in to a preset station 1 Follow steps 1 to 2 in "Manual tuning" and select the AM or FM band. 2 Press one of the STATION SELECT PRESET buttons where the desired station is stored. To set the alarm 1 Press and hold ALARM SET A or B. "WAKE UP" appears and the hour flashes in the display. To display the year and date The STATION SELECT tactile dot. PRESET 3, VOLUME + and iPod & iPhone buttons have a Press SNOOZE/DATE/SLEEP OFF (SNOOZE on the remote) once for the date, and press it again for the year. After a few seconds, the display will change back to the current time automatically. 3 Adjust the volume using VOLUME + or ­ (VOL + or ­ on the remote). The preset station can also be selected by PRESET + or ­ on the remote. 2 Press TIME SET + or ­ repeatedly until the desired hour appears. Press and hold TIME SET + for at least 2 seconds to move the alarm time forwards. Press and hold TIME SET ­ for at least 2 seconds to move the alarm time back. When you release the button, the changed time will flash for about 2 seconds. To change the alarm time again, press TIME SET + or ­ within these 2 seconds, otherwise the setting change will be fixed as displayed. To turn off the unit before the preset time Press SNOOZE/DATE/SLEEP OFF (SNOOZE on the remote) or OFF/ALARM RESET (OFF on the remote). To change the sleep timer setting To doze for a few more minutes You can press SLEEP repeatedly to select the desired sleep timer setting even after the sleep timer has been activated. ­Auto preset tuning 1 Follow steps 1 to 2 in "Manual tuning" 2 3 and select the AM or FM band. Press and hold RADIO BAND until "AP" flashes in the display. Press DISPLAY/MEMORY. The unit automatically presets the available channels in order. 3 Press iPod & iPhone . 3 Press ALARM SET A or B. The minute flashes. To cycle the hour rapidly, press and hold TIME SET + or ­. Setting the brightness of the display Three levels of brightness are available by pressing BRIGHTNESS. 4 Adjust the volume using VOLUME + or ­ (VOL + or ­ on the remote). To Turn off the iPod Pause playback Press OFF, or press and hold iPod & iPhone iPod & iPhone To resume play, press it again. [. . . ] If you are using an iPhone or iPhone 3G, attach the supplied universal dock adapter for iPhone or iPhone 3G before inserting into the connector. The adapter number, or , is shown on the bottom-rear of the supplied universal dock adapters. is for the iPhone, and is for the iPhone 3G. Check the adapter number before use. * During playback, this operation goes back to the beginning of the current track. [. . . ]