User manual SONY ICF-C900

[. . . ] Proper registration will enable us to send you periodic mailings about new products, services, and other important announcements. Registering your product will also allow us to contact you in the unlikely event that the product needs adjustment or modification. Thank you. Battery may explode if mistreated. Do not recharge, disassemble or dispose of in fire. [. . . ] If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. CR2032 1 Remove only the loop part from the 2 Set up the AM loop antenna. plastic stand. Precautions Play the unit on the power source specified in "Specifications. " To disconnect the AC power cord (mains lead), pull it out by the plug, not the cord. The unit is not disconnected from the AC power source (mains) as long as it is connected to the wall outlet, even if the unit itself has been turned off. Since a strong magnet is used for the speaker, keep personal credit cards using magnetic coding or spring-wound watches away from the unit to prevent possible damage from the magnet. Do not leave the unit in a location near a heat source such as a radiator or airduct, or in a place subject to direct sunlight, excessive dust, mechanical vibration, or shock. Allow adequate air circulation to prevent internal heat build-up. Do not place the unit on a surface (a rug, a blanket, etc. ) or near materials (a curtain) which might block the ventilation holes. Should any solid object or liquid fall into the unit, unplug the unit and have it checked by qualified personnel before operating it any further. To clean the casing, use a soft cloth dampened with a mild detergent solution. To change the alarm time again, press ALARM/TIME SET + or ­ within these 2 seconds, otherwise the setting change will be fixed as displayed. Audio connecting cable (supplied) To external equipment 2 Press AUDIO IN to display "AUDIO IN. " 3 Play the equipment connected to the 4 Adjust the volume using VOLUME + or ­. To return to the radio Press RADIO BAND. The frequency is shown in the display. AUDIO IN jack. To doze for a few more minutes Setting the clock manually 1 Plug in the unit. 2 Press and hold CLOCK for at least 2 seconds. The display shows the frequency for about 10 seconds, and then returns to the current time. To preset another station, repeat these steps. Note If you try to store another station with the same preset number, the previously stored station will be replaced. Press SNOOZE/DATE/SLEEP OFF. The sound turns off but will automatically come on again after about 10 minutes. You can change the snooze time by pressing SNOOZE/DATE/SLEEP OFF repeatedly within 4 seconds. The maximum length of the snooze time is 60 minutes. To return to the iPod To stop listening Press iPod & iPhone . Press OFF, and stop playback on the connected unit. Notes Refer also to the connected equipment's manual. The supplied audio connecting cable may not be used with some external equipment. [. . . ] When using an iPod touch/iPhone To wake up to music stored in an iPod touch/ iPhone, connect the iPod touch/iPhone to the unit first, follow the steps above to set alarm time, and then select the music function. Even if the iPod alarm setting is complete, if you turn the iPod touch/iPhone power off before the unit, the iPod alarm will not work. display, press ALARM TIME SET A or B again. Setting the sleep timer You can fall asleep to the music, etc. , using the built-in sleep timer that turns off the unit automatically after a preset duration. 1 Press SLEEP while the unit is turned on. 2 Press SLEEP to set the sleep timer duration. Setting the radio alarm "SLEEP" appears and the sleep time flashes in the display. 1 Perform steps 1 to 8 in "To set the 2 2 Press and hold BRIGHTNESS/ TIME ZONE for at least 2 seconds. The current EST (Eastern Standard Time) appears in the display. 3 Press ALARM TIME SET + or ­ Area number "2" flashes in the display. When daylight saving time (summer time) begins This model automatically adjusts for daylight saving time (summer time). " " is displayed from the beginning of daylight saving time (summer time) and disappears at the end of daylight saving time (summer time) automatically. [. . . ]