User manual SONY ICF-CD803

[. . . ] Do not install the appliance in a confined space, such as a bookcase or built-in cabinet. As the main plug is used to disconnect the unit from the mains, connect the unit to an easily accessible AC outlet. Should you notice an abnormality in the unit, disconnect the main plug from the AC outlet immediately. Notice for customers: the following information is only applicable to equipment sold in countries applying EU directives The manufacturer of this product is Sony Corporation, 1-7-1 Konan, Minato-ku, Tokyo, Japan. [. . . ] The disc should be inserted with the label side up. Dusty or defective disc -- Clean the disc with an optional cleaning cloth. Take out the CD and leave the CD compartment open for about an hour to allow condensation to evaporate. Compatible iPod models The compatible iPod models are as follows. Update your iPod to use the latest software before you use it. 4 Make sure the AM loop aerial is Adjusting the AM loop aerial Notes Do not charge the battery. When you are not going to use the remote commander for a long time, remove the battery to avoid any damage caused by leakage and corrosion. connected firmly by pulling softly. Find a place and an orientation that provide good reception. Do not place the AM loop aerial near the unit or other AV equipment, as noise may result. Tip Adjust the direction of the AM loop aerial for best AM broadcast sound. Knowing when to replace the battery When the battery becomes weak, "" appears in the display. If a power interruption occurs while the battery is weak, the current time and alarm will be initialized. Replace the battery with a Sony CR2032 lithium battery. Use of another battery may cause a fire or explosion. Note If "12:00" flashes in the display when the unit is connected to AC outlet for the first time, the battery may be weak. "REP SHUF" (shuffle repeat) All the tracks are played repeatedly in random order. To cancel Automatic DST/Summer Time adjustment during the daylight saving time (summer time) period The CD, iPod & iPhone and VOLUME + buttons have a tactile dot. The Automatic DST/Summer Time adjustment can be cancelled. Press and hold CLOCK and BRIGHTNESS at the same time while the clock is displayed. "Auto OFF" appears in the display to show that Automatic DST/Summer Time adjustment has been cancelled. Notes The change timing of Automatic DST/Summer Time adjustment employed by the unit (see above) is subjected to variation by circumstances and the law in each country/ region. In such a case, cancel the Automatic DST/Summer Time adjustment and set the DST display manually as necessary. Customers living in a country/region that does not use the daylight saving time (summer time) must cancel Automatic DST/Summer Time adjustment before using the unit. To activate Automatic DST/Summer Time adjustment again, press and hold CLOCK and BRIGHTNESS at the same time. "Auto ON" appears in the display to show that Automatic DST/Summer Time adjustment has been activated. The display returns to the clock. Tip If the FM broadcast is noisy, press MODE to turn off "ST" in the display. The radio becomes clearer although the sound becomes monaural. Notes on radio reception 2 Press CD . 3 Press VOLUME + or ­ repeatedly to adjust the volume. To Pause Resume play after pause Cue to the beginning of the current track (AMS*) Go back at high speed Go forward at high speed Locate a previous track (AMS*) Locate a succeeding track (AMS*) Stop play Press CD "CD" appears in the display to indicate the CD is playing. Keep digital music players or mobile phones away from the AM loop aerial or the FM aerial, as this may lead to interference of reception. When you are listening to the radio with an iPhone connected to the unit, interference with radio reception may occur. [. . . ] Please be aware that among those discs, there are some that do not conform to the CD standard and may not be playable by this product. To handle compact discs Correct Handle the disc by its edge. Presetting a station 1 Follow steps 1 and 2 in "Manual tuning" to tune the frequency you wish to preset. 2 Hold down MEMORY/DISPLAY for at least 2 seconds. 3 Press PRESET + or ­ to select the preset number, then press MEMORY/DISPLAY. The frequency is stored with the selected preset number. repeatedly until the desired hour appears. To set the hour rapidly, hold down ALARM TIME SET + or ­. [. . . ]