User manual SONY ICS-FW40D

[. . . ] 4 Main Folder. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 HTTP Document Root . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Installation Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Make sure none of the following software packages are already installed. If they are, then uninstall them before proceeding. o Any HTTP Server listening to Port 80 Apache IIS etc o Any FTP Server listening to Port 21 o MySQL (All versions) 2. Close all other applications that might be running. Version- 1. 0a -5­ www. technovare. com FW40 Commander Software Users Guide© Installation and Setup, continued Installation 3. Insert Installation CD into Target PC's CD ROM drive. Once you select the "Install SW" option on the CD Menu, the installation process should start. In case it does not, then browse to the CD drive in "My Computer" and run "setup. exe" to begin the installation process. Follow the "On Screen" instructions. If there were no problems detected by the Compatibility Checker, you should see this dialog: If there were any problems detected, then they will be listed in the Compatibility Checker log. You must take care to clear up the problems or else the installer will refuse to install the software. It gives you the chance to retry the compatibility check as many times as you need. Version- 1. 0a -6­ www. technovare. com FW40 Commander Software Users Guide© Installation and Setup, continued 6. There will be a series of Question popup dialog boxes near the end of the installation process. They are related to the FileZilla FTP server installation. Please answer them as shown below: Version- 1. 0a -7­ www. technovare. com FW40 Commander Software Users Guide© Installation and Setup, continued 7. You should see the following screen if all was successful. Version- 1. 0a -8­ www. technovare. com FW40 Commander Software Users Guide© Installation and Setup, continued Setup Edit Index. html Open the file "c:\FW40Cmdr\www\Index. html". Replace both instances of "localhost" with the IP Address (or domain name) of your server on the LAN. If you do not know the IP Address, then open a "cmd" window and type "ipconfig". This can be done using a string replacement feature of any text editor by replacing "localhost" with "192. 168. 0. 10" (as an example IP Address). Version- 1. 0a -9­ www. technovare. com FW40 Commander Software Users Guide© Using the Software Server-Side Controls Starting the Services The newly installed services (Apache2, MySQL, FW40CmndrWinService, FileZilla) should all be started after a successful installation and upon any subsequent reboots of the server. If, for some reason, the services are not running, you can restart them by: Start->All Programs->FW40CmdrServer->Start Services Stopping the Services Before uninstalling, or if you just want the take the server offline, you need to stop the FW40Commander Windows Service and the other services by: Start->All Programs->FW40CmdrServer->Stop Services Version- 1. 0a - 10 ­ www. technovare. com FW40 Commander Software Users Guide© Using the Software, continued Rich Internet Application (Client Browser) Now that your server is online, you should enter the domain name or IP Address of your server into your browser's address bar. This resulting Rich Internet Application is the main point of control for the system. Any web client that is able to access your server, can also serve as a point of control for the system. Version- 1. 0a - 11 ­ www. technovare. com FW40 Commander Software Users Guide© Using the Software (Settings) Settings Screen The Settings Screen provides the functions needed to add devices, streams, files, and create playlists to name a few. The following tabbed pages exist under the Settings screen: Devices Groups Files Streams Playlists Version- 1. 0a - 12 ­ www. technovare. com FW40 Commander Software Users Guide© Using the Software (Settings), continued Adding Devices Step 1: Enter a name for the new device Step 3: Press the "Add" button Step 2: Enter the IP Address For in. [. . . ] Only if the group is comprised of only FW40D devices, will all available playlists be displayed. Version- 1. 0a - 26 ­ www. technovare. com FW40 Commander Software Users Guide© Using the Software (Main), continued Scheduling Events Step 1: Select a Device or Group Step 2: Select a Date Step 3: Use these controls to create a new Scheduled Event This is screen in which you can create scheduled events. This ability to schedule files or playlists that contain files will only be enabled for FW40D devices and groups that only contain FW40D devices. The list of files to select from is comprised of all the files local to a particular device. For a group, it is comprised of the `intersection' set of files within a group. Version- 1. 0a - 27 ­ www. technovare. com FW40 Commander Software Users Guide© Using the Software (Main), continued Displaying and Saving Logs Step 1: Select a Device or Group Step 2: View Log Step 3: Download Log file. The activities of a device or group can be viewed from this screen. [. . . ]