User manual SONY JH1-JH3 OPERATING MANUAL

[. . . ] DIGITAL VIDEOCASSETTE COMPACT PLAYER J-H1 J-H3 i. LINK INTERFACE BOARD HKJ-101 OPERATION MANUAL 1st Edition (Revised 1) [English] English WARNING To prevent fire or shock hazard, do not expose the unit to rain or moisture. To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only. · Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. [. . . ] (When AUTO REWIND, extended menu item 125, is set to ENA) Note In jog mode, the JOG dial controls the playback speed based the speed at which the dial is turned. The playback speed range is ±1 times normal speed. Use the following procedure to carry out playback in shuttle mode. 1 Turn the JOG dial directly or press the JOG/ SHUTTLE button to light the JOG indicator. Pressing the JOG/SHUTTLE button toggles between jog mode and shuttle mode. 2 Turn the JOG dial in the desired direction, at a speed corresponding to the desired playback speed. Playback in jog mode starts. This unit uses an auto-tracking function. The factory setting for the auto-tracking is on (AUTO TRACKING ON). For details on how to change the setting, contact your nearest Sony dealer. While this unit is pulling the tape in, the PLAY button indicator B flashes. 3 To stop playback in jog mode, stop turning the JOG dial. It is possible to make pressing the JOG/SHUTTLE button to switching between JOG and SHUTTLE mode. Select "KEY" in SELECTION FOR JOG/ SHUTTLE DIAL ENABLE, extended menu item 101, to enable the above feature. (This is the default setting. ) Chapter 4 Playback 4-3 4-2 Playback Procedures 4-2-3 Playback in Shuttle Mode 2 Turn the SHUTTLE dial to the angle corresponding to the desired playback speed. Playback in shuttle mode starts. 1 3 Return the SHUTTLE dial to the center indent position or press the STOP button to cancel shuttle mode playback. It is possible to make pressing the JOG/SHUTTLE button to switching between JOG and SHUTTLE mode. Select "KEY" in SELECTION FOR JOG/ SHUTTLE DIAL ENABLE, extended menu item 101, to enable the above feature. (This is the default setting. ) Chapter 4 Playback 3 1, 2, 3 To return to normal-speed playback Press the PLAY button. To alternate between normal-speed playback and shuttle mode playback Set the SHUTTLE dial to the position corresponding to the desired shuttle playback speed first. Press the PLAY button, and then press the JOG/SHUTTLE button twice. For intermittent shuttle mode playback, press the STOP button first and then press the JOG/ SHUTTLE button twice. Normally, you turn the SHUTTLE dial after setting the jog/shuttle mode by pressing the JOG/ SHUTTLE button. You can also set the jog/shuttle mode, however, by directly turning the dial. (This is available when SELECTION FOR JOG/ SHUTTLE DIAL ENABLE, extended menu item 101, is set to DIAL. ) In this case, you must reset the SHUTTLE dial to the center position after turning it, otherwise the dial is moved by vibration and the tape may start running in the shuttle mode during playback. In shuttle mode, the SHUTTLE dial controls the playback speed based on the angular position of the dial. There are seven playback speeds: ±0. 03 times, ±0. 12 times, ±0. 5 times, ±1 times, ±2 times, ±5 times, ±21 times. [. . . ] H02: DRUM RUNNING mode Displays the total number of hours the drum has run with tape threaded in units of 1 hour. H03:TAPE RUNNING mode Displays the total number of hours the unit has been in fast forward, rewind, playback, or search (except for stop and still) mode in units of 1 hour. H04:THREADING mode Displays the total number of times the tape has been threaded/unthreaded. H06:REEL SHIFT mode Displays the total number of times that the reel has been shifted according to the size of the cassette (L cassette or S cassette) in use. [. . . ]