User manual SONY KDE-37XS955

[. . . ] If something smells strange or smoke comes from the monitor: Turn off the monitor and disconnect the power plug from the power point immediately. Contact service center after confirming that the smoking has stopped. If you continue to operate the monitor with such abnormal condition, it may cause fire or you may receive an electric shock. Do not drop water or a foreign substance on to the monitor. [. . . ] Consult your dealer before attempting to install this projector on the desk-top stand. In order to prevent an internal temperature increase, maintain a space of 10cm or more between the sides and other objects such as walls, etc. , so that the ventilation holes are not blocked. * WARNING CAUTION Anti-tumble measures CAUTION Have this unit mounted in a stable place. Take measures to prevent it from tumbling down to avoid possible physical injury. Securing to a wall or post 1)After positioning, pass the hooks included with the Desk-top Stand through the holes located on both ends (left and right) at the top and fasten with M4 screws, as shown in the diagram. 2)Using a commercially available cord, chain and clamp, secure the set to a firm wall or post. Securing desktop 1)Using wood screws (two), fasten the set to the clamping screw holes on the rear of the stand as shown. 2)Using commercially available wood screws, secure the set firmly in position. Wood screw Two places 3 INSTALLATION INSTRUCTIONS (continued) Component Names Front ENGLISH The Adjustment button is located on the bottom. RGB/ VIDEO MENU Panel Cabinet (front frame) Remote-control sensor 8 Stand Control panel STANDBY (RED) ON (GRN) Indicating lamp SELECT VOLUME SUB-POWER 9 Main power switch 9 Subpower button VOLUME button SELECT button 12 10 9 MENU button RGB/VIDEO button 12 10 4 External device connection terminals AUDIO IN SPEAKER TERMINAL (88W) L/MONO R R L VIDEO2 Nearer Terminal Further Terminal PR/CR PB/CB Y VIDEO S V H B G R RS232C IN COMPONENT IN VIDEO1 COMPOSITE IN D-SUB IN RGB1 RGB2 L/MONO R Nearer Terminal Further Terminal AUDIO IN External speaker terminals Video input terminal 7 RGB input terminals 6 Remote controller POWER button 9 POWER RECALL RGB/ VIDEO 10 RGB/VIDEO button RECALL button 11 MUTE button 11 MUTE VOLUME 10 VOLUME button MENU MENU button 12 SELECT 11 SELECT button 5 ENGLISH Rear INSTALLATION INSTRUCTIONS (continued) Installation and Cabling Connecting to the PC Read Usage Notes ( to ) carefully to ensure maximum safety before proceeding to these steps: 1) Make sure that the display signals produced by your PC meet the specifications of this product. For the specifications of this product, see Product Specifications ( Install the monitor to have ready access to a power socket. 25 ENGLISH 6 to 26 ). 2) Choose an appropriate site and install the product on a level table where the stand is secure. 3) Make sure that the monitor's power switch is off. The monitor is shipped with the power switch off. 4) Make sure that your PC's power switch is off. 5) Interconnect the signal input terminal (RGB1) on the monitor rear panel and the display signal output terminal of the PC to each other using the signal cable included. Optional cables are needed to connect to the RGB2 input and audio input terminals. If the signal cable included does not match your PC, consult your dealer after reading the section "Signal Input". 26 6) Insert one end of the power cable included into the rear-panel power cable connector and the other end into a power socket. 7) Turn on the monitor, then the PC to make sure that a display image appears on the monitor screen. For instructions on turning on the monitor and adjusting its display images, see "Operating Instructions" ( 9 to 16 ). Monitor rear panel PC To audio output terminal To signal output terminal To signal output terminal Power cable Power cable connector AUDIO IN To audio input terminals RGB1 D-SUB IN RGB2 L/MONO R V H B G R RS232C IN Nearer Terminal Further Terminal To signal output terminals To signal output terminals (such as a video disc player, a DVD player, or a video camera) Read Usage Notes ( to ) carefully to ensure maximum safety before proceeding to these steps: 1) Choose an appropriate site and install the product on a level table where the stand is secure. Install the monitor to have ready access to a power socket available. 2) Make sure that the monitor's power switch is off. The monitor is shipped with the power switch off. 3) Make sure that the video equipment's power switch is off. 4) Interconnect the signal input terminal on the monitor rear panel and the video equipment's signal output terminal to each other using an optional cable. While the guidance is on display, press or to turn up the volume. While the guidance is on display, press or to turn down the volume. You can also adjust the sound volume setting via the on-screen display system, EasyMenu 12 The sound volume adjustment mode will exit when no keys are entered for 5 seconds. (The adjustment status guidance will disappear automatically. ) Remote controller VOLUME Sound volume setting VOLUME : 30 Set unit VOLUME Adjustment status guidance Contrast Adjustment ENGLISH 11 While the on-screen display system, EasyMenu 12 , is not on display, press the remote controller SELECT button or to adjust the contrast. When you press these buttons, the status of contrast adjustment and the input horizontal (H) and vertical (V) frequencies of the input signal will be displayed in a guidance image. While the guidance is on display, press the key to narrow the difference between darkness and brightness. While the guidance is on display, press the key to widen the difference between darkness and brightness. You can also adjust the contrast setting via the onscreen display system, EasyMenu 12 The contrast adjustment mode will exit when no keys are entered for 5 seconds. (The adjustment status guidance will disappear automatically. ) Contrast setting Remote controller SELECT CONTRAST : 100 H: **. *Hz Input vertical frequency Input horizontal frequency Adjustment status guidance Sound Mute Press the remote controller MUTE button to mute the sound temporarily. When you press the button, [MUTE] (pink) and the status of volume setting will be displayed in a guidance image. While the sound is muted, press the volume. While the sound is muted, press the button to turn down the button to cancel the mute. (The display will turn to pink. ) Remote controller MUTE Sound volume setting MUTE : 30 You can also adjust the sound volume setting of the mute via the on-screen display system, EasyMenu 12 Press the remote controller MUTE button once again and the mute will be canceled and the guidance will change to VOLUME (blue), enabling the volume to be heard. When MUTE is used, the guide display will continue for 5 sec. [. . . ] Adjusting the phase will reduce the horizontal stripes. See page ENGLISH 22 The temperature of the display panel surface is high. There are locations on the screen that are different from the periphery (*). *Points that do not light, points with brightness different from that of the periphery, points with color different from that of the periphery, etc. Vertical stripes appear, depending on the screen contents. Coarse horizontal stripes appear in FULL display. ( durning personal computer signal input) Actions to Correct Abnormal Displays ENGLISH 23 Depending on the kind of system equipment used, images may not be displayed normally. In this case, make the adjustments suggested below. Symptom 1 Text displayed across the screen appears vertically streaked, with some characters blurred (display 1). [. . . ]