User manual SONY KDL-37P302H annexe 1

[. . . ] When an alternative type of plug is used it should be fitted with a 10 AMP FUSE otherwise the circuit should be protected by a 10 AMP FUSE at the distribution board. If the plug supplied with this equipment has a detachable fuse cover, be sure to attach the fuse cover after you change the fuse. Never use the plug without the fuse cover. If you should lose the fuse cover, please contact your nearest Sony service station. [. . . ] Because map information is downloaded from the Internet online map service, the network connection must be required and the TV has to be connected to the network (page 30). 7 Select "OK", then press . The GPS log files are loaded. 8 Disconnect the GPS unit and connect the device on which the photograph is stored. 9 Select a photograph (page 26). 10 Press the green/red buttons to zoom in/out on the map. 1 Select a photograph (page 26). 2 Press the green/red buttons to zoom in/out on the map. To change the display position of the map on the TV screen, press the blue button repeatedly. ~ · Because the Internet online map service is provided by a third party, service may be changed or terminated without prior notification to the user. · The position indicated on the map may differ depending on the image capture device. · Only a large-scale map that cannot be zoomed in or out is displayed if the TV is not connected to the Internet or the Internet online map service is terminated. · You can also display a slideshow with the location on the map. Set "Photo Set-up" to "Simple with map" (page 26). z · A map can be displayed in the case of photograph's EXIF data includes a date information, and the associated longitude and latitude information ("Log files") has been recorded using a Sony GPS unit. Follow the procedure described below. 1 2 3 4 Connect the GPS unit to the USB port. Press G/g to select "Photo. " Press F/f to select the GPS unit, then press . 28 GB To make the control for HDMI settings Using BRAVIA Sync with Control for HDMI The control for HDMI function enables the TV to communicate with the connected equipment that is compatible with the function, using HDMI CEC (Consumer Electronics Control). Press the yellow button to switch between "List View" and "Thumbnail View. " If network devices do not appear, follow the steps on page 32. Connecting the TV to the Network TV 4 Press F/f/G/g to select a file or folder, then press . When you select a folder, select a file, then press . Playback starts. Network cable (not supplied) z · A map can be displayed with a photograph in the case of longitude and latitude information has been recorded to photograph's EXIF data (page 28). Broadband router ~ · Depending on the network device, it may be necessary to register the TV with the network device. · Picture quality may appear coarse when using (Photo) because images may be enlarged depending on the file. Also, images may not fill the entire screen depending on the image size and aspect ratio. · Some photo files may take some time to be displayed when using (Photo). · The file name and folder name support only English. · To play the files which are received from a network device, they need to have one of the following file formats. ­ Still images: JPEG format ­ Music: MP3 format or linear PCM format Depending on the network device, the file format may be converted before transfer. In such cases, the file format resulting after conversion is used for playback. For details, see the instruction To network device Network cable (not supplied) DSL modem/ Cable modem Internet 30 GB manual for the network device being used. [. . . ] · Check that the server is correctly configured. · Check that the selected equipment is connected to the network and can be accessed. · If the "IP Address Settings" in "Network" under "Network Settings" is set to "DHCP (DNS automatic)" or "DHCP (DNS manual)", it may take some time to recognise a device if there is no DHCP server. Execute "Server Diagnostics" (page 33). 52 GB Condition Explanation/Solution The TV cannot be found from Check Connections renderer-compatible · Check that the LAN cable and/or mains lead of the server has not equipment (the controller) become disconnected. Check Settings · Check if the "Renderer Function" is activated (page 46). [. . . ]