User manual SONY KDS-R50-60XBR1 QUICK START

[. . . ] 2-637-152-11(1) 1 KDS-R50XBR1 KDS-R60XBR1 Connecting Your TV Review the following chart to determine which diagram to use to connect the components in your system: Turn off and unplug all components before making connections. Re ce iv er Ca bl e HD Bo x Making Audio/Video Connections Your new TV includes various types of video inputs and two types of audio jacks; composite-RCA type and digital audio (optical). Use the outputs/inputs that are available on your components that provide the best video/audio performances: Best Audio/Video Performance Re co rd er Dr ea So m ny Sy st em Ca bl e e Please follow these steps to setup your TV: Connector type Connector type HDMI (High-Definition Multimedia Interface) VCR CableCARD (optional) 1 zzz Connecting Your TV (See reverse side) PCM/DOLBY DIGITAL DIGITAL AUDIO (OPTICAL OUT) Digital Optical Digital Coaxial Will require an adapter to connect to this TV's digital audio input. DVD Player PC DVI (Digital Visual Interface) Will require an adapter to connect to this TV. Cable Box VCR DVD Player 2 zzz Running Initial Setup PC Analog Audio Component video Satellite Receiver AV Receiver S VIDEO Composite video Programming the Remote Control Cable Box VCR DVD Player 3 RF/Coaxial Satellite Receiver Activating CableCARDTM Service Before you can use CableCARD service, you need to insert the CableCARD device (supplied by your cable provider) and activate the service. Inserting the CableCARD incorrectly may result in permanent damage to the card and the TV. [. . . ] Wide Mode: Selecting the appropriate screen mode will increase enjoyment of your TV viewing. When watching a Standard Definition source (4:3 aspect ratio) on this TV, you will see bars on both the left and right sides of the screen. Press the WIDE button on your remote to cycle through different screen modes to fill the screen in various ways. (Wide Zoom enlarges the center, Normal is how your TV receives the signal, Full stretches horizontally and Zoom enlarges the image proportionately to fill the screen. ) When watching a High Definition source (16:9 aspect ratio) on this TV, you will see the screen filled with an image. Press the WIDE button on your remote to toggle through different screen modes, especially zooming in to the center of the screen. (Wide Zoom enlarges the center, Full displays the image at its original size, Zoom enlarges the image proportionately to fill the screen. ) When the TV receives a 720p or 1080i formatted signal, the Normal mode is not available. See the "Using the WIDE Button" section of the manual. If you have video equipment other than Sony brand that you want to control with the TV's remote control, use the following procedures to program the remote control. The equipment must have infrared (IR) remote capability in order to be used with this remote control. 3 Satellite Receivers Manufacturer Sony Dish Network Echostar General Electric Hitachi Hughes Mitsubishi Panasonic RCA/PROSCAN Toshiba Code 801 810 810 802 805 804 809 803 802, 808 806, 807 Initial Setup automatically creates a list of receivable channels from both VHF/UHF antenna and cable TV channels if both sources are connected. When Initial Setup is complete, the TV will display the total number of analog channels and the total number of digital channels found. Using the code list below, find the three-digit code number for the manufacturer of your equipment. (If more than one code number is listed, use the number listed first. ) 2 1 Laserdisc Players Manufacturer Sony Panasonic Pioneer Code 701 704, 710 702 1 Press 2 Press repeatedly until the DVD/VCR, SAT/ CABLE or i. LINK indicator lights up. for five seconds until the indicator of the selected input flashes. VCRs Manufacturer Sony Admiral (M. [. . . ] See the Operating Instructions for details on using CableCARD. * Cable box may not be required if using CableCARD. See the Operating Instructions for details. * Cable box may not be required if using CableCARD. [. . . ]