User manual SONY KLH-W32/T

[. . . ] These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: s s s Reorient or relocate the receiving antenna. [. . . ] This section provides some of the individual connections you can make. For multiple connections, please refer to the Quick Setup Guide. Connecting the TV VCR, Cable and Antenna This scenario shows a VCR with Cable signals connected through the video inputs and the Antenna connected through the VHF/UHF input. The Cable or VCR signals are selected by the VCR through the video inputs while TV signal is selected by the TV tuner. To connect the VCR and cable z The most common setup is the Cable input into the VCR Antenna IN, the VCR Antenna Out to the VHF/UHF input. 1 Connect the CATV cable to the VCR's VHF/UHF input jack. 2 Connect the supplied 75-ohm coaxial cable from the antenna to the TV's VHF/UHF input jack. 3 Use A/V and S VIDEO cables to connect the VCR's AUDIO and S VIDEO output jacks to the TV's AUDIO and S VIDEO input jacks (VIDEO 1 IN). 4 Run the Initial Setup Program, as described in "Setting Up the Channel List" on page 31. If your VCR is not equipped with S VIDEO, use a VIDEO cable (yellow) instead of the S VIDEO cable. (Continued) 25 Connecting the TV KLV-S15G10 CATV cable VCR Rear of TV VIDEO 3 IN (480p/480i) PR PB Y R VIDEO 1 IN R AUDIO L S VIDEO (MONO) VIDEO AUDIO OUT R L VHF/UHF AUDIO L S VIDEO cable S VIDEO AUDIO-R (red) AUDIO-L (white) VIDEO (yellow) 75-ohm coaxial cable A/V cable 26 Connecting the TV KLV-S20G10 CATV cable VCR Connecting the TV Rear of TV VHF/UHF VIDEO 4 IN (480p/480i) R-AUDIO-L VIDEO 3 IN R-AUDIO-L(MONO) VIDEO PR PB Y R-AUDIO-L(MONO) VIDEO S VIDEO VIDEO 1 IN 75-ohm coaxial cable A/V cable AUDIO-R (red) AUDIO-L (white) VIDEO (yellow) S VIDEO S VIDEO cable Notes on Using This Connection To Do This . . . Do This . . . Watch the VCR Watch cable channels Set up the remote control to operate the VCR Activate the remote control to operate the VCR Control VCR functions with the remote control Label video inputs to easily identify equipment connected to the TV Press TV/VIDEO repeatedly to select the VCR input (Video 1, 2 or 3 for KLH-W32/T). Press TV/VIDEO repeatedly to select the VCR input (Video 1, 2 or 3 for KLH-W32/T). See "Programming the Remote Control" on page 34. See "Operating a VCR" on page 36. See the instructions for setting up Label Video Inputs on page 51. 27 Connecting the TV DVD Player For best results, use this connection if your DVD player has component video (YPBPR) jacks. To connect a DVD player with component video connectors 1 Use a component video cable to connect the DVD player's YPBPR output jacks to the TV's YPBPR input jacks (VIDEO 3 IN (KLVS15G10) or VIDEO 4 IN (KLV-S20G10)). The YPBPR jacks on your DVD player are sometimes labeled Y, CB and CR, or Y, B-Y and R-Y. If so, connect the cables to their matching color jacks. 2 Use an audio cable to connect the DVD player's AUDIO output jacks to the TV's AUDIO input jacks (VIDEO 3 IN (KLV-S15G10) or VIDEO 4 IN (KLV-S20G10)). The YPBPR jacks do not provide audio, so audio cables must be connected to provide sound. KLV-S15G10 Rear of TV VIDEO 3 IN (480p/480i) PR PB Y R VIDEO 1 IN R AUDIO L S VIDEO (MONO) VIDEO AUDIO OUT R L AUDIO L PR PB Component video cable Y DVD Player AUDIO-R (red) AUDIO-L (white) Audio cable 28 Connecting the TV KLV-S20G10 Rear of TV VIDEO 4 IN (480p/480i) R-AUDIO-L VIDEO 3 IN R-AUDIO-L(MONO) VIDEO AUDIO-L (white) AUDIO-R (red) PR PB Y Connecting the TV R-AUDIO-L(MONO) VIDEO S VIDEO VIDEO 1 IN Audio cable DVD Player Y PB PR Component video cable Notes on Using This Connection To Do This . . . Do This . . . Watch the DVD player Set up the remote control to operate the DVD player Activate the remote control to operate the DVD player Control DVD functions with the remote control Label video inputs to easily identify equipment connected to the TV Press TV/VIDEO repeatedly to select the DVD player input or Video 4. Press to jump back and forth between two channels. The TV alternates between the current channel and the last channel that was selected. Press to display the Favorite Channels list. See "Using Favorite Channels" on page 37. Press to have the remote control operate the equipment you want. See "Programming the Remote Control" on page 34. When FUNCTION is switched on VCR/DVD, these buttons operate the video equipment you have programmed into the remote control. See "Using Other Equipment with Your Remote Control" on page 36. m Rewind N Play M Fast forward z Record (by pressing z and N) X Pause x Stop Press to freeze the picture. The current program appears in the sub screen when freeze is selected. You can use this feature to write down information such as phone numbers, recipes, etc. [. . . ] If it is set to Off, sound is not output from the TV's speakers regardless of the TV's volume control. Make sure that the antenna is connected using the supplied 75-ohm coaxial cable. Keep the antenna cable away from other connecting cords. Do not use 300-ohm twin lead cables as interference may occur. [. . . ]