User manual SONY KP-41PX1K

[. . . ] Thank you for choosing this Sony projection TV. Before operating the projection TV, please read this manual thoroughly and retain it for future reference. Reading and Understanding this Instruction Manual: · Use Getting Started if you wish to install the projection TV set and to get familiar with the basic functions. ⷠUse Advanced Operati if you wish to know more about the additional features of the projection TV set. [. . . ] If you wish a more accurate convergence adjustment , then push to z to enter Lines in red and blue) you want to adjust. : red vertical line (left/right adjustment) : red horizonta line (up/down adjustment) : blue vertical line (left/right adjustment) : blue horizontal line (up/down adjustment) Line with the green line in the centre, then press OK to confirm. 6 Repeat steps 4 and 5 to adjust the other lines, until all the lines have Your projection TV is ready for use. (For more details, please refer to the section "Automatically Tuning the TV using the Remote Control") Besides the explanation in the section "Automatically Tuning the TV using the Remote Control", by following the instructions below, this projection TV also searches and stores automatically all available channels using just one button of the projection TV set and one button of the remote control. 1 Push up the flap on the front of the projection TV to reveal the front Button on the TV set for some seconds, until a menu appears automatically on the screen asking you to check that antenna is connected. Please, be patient and do not press any button, otherwise the automatic tuning will not be completed. When the automatic tuning procedure is complete, the Programme Sorting menu appears on the screen: · If you do not wish to change the channel order, press the MENU button on the remote control to exit and return to the normal TV screen. ⷠIf you wish to change the channel order, proceed in the same way as described in the chapter "Changing the Programme Order of the TV channels", section b). Use this function to preset channels or a video input source one by one to the programme order of your choice. 4 Push the joystick to $ or 4 to select on which programme number You want to preset a channel, then push to z. 7 Press the number buttons to enter the channel number of the TV Broadcast or push the joystick to 4 or $ to search for the next available channel. If you do not wish to store this channel, push the joystick to 4 or $ to continue searching for the desired channel. 8 If this is the desired channel you wish to store, press the OK button. 9 Repeat steps 4 to 8 if you wish to store more channels. 10 Press the MENU button to exit and return to the normal TV screen. Your projection TV is now ready for use. With this feature you can: a) Even normally the automatic fine tuning (AFT) is operating, however you can manually fine-tune the TV to obtain a better picture reception if the picture is distorted or b) preset the AV3 output for the programme positions of channels with scrambled signals (eg from a pay TV decoder). In this way a connected VCR records the unscrambled signal. Symbol, then push to z to enter Push the joystick to $ or 4 to select Further Programme Preset, then push to z . Push the joystick to $ or 4 to select the relevant programme number, then push to z repeatedly to select: Repeat steps 4 and 5a) if you wish to fine tune other channels. b) DECODER Push the joystick to $ or 4 to select AV3 and press the OK. The picture from the decoder connected to the Euro AV :3 on the back of the projection TV will appear on this programme number. [. . . ] ⷠIf your video equipment has a COMMAND MODE selector, set this selector to the same position as the VTR 1234 DVD selector on the TV Remote Control. ⷠIf the equipment does not have a certain function, the corresponding button on the remote control does not work. Using this function you can record on your VCR any signal coming from an external equipment connected to the Euro AV connectors :2/q 2 or :3 placed on the rear of the projection TV. In that case you have to select the output source as described below (if your VCR support Smartlink, this procedure is not necessary). [. . . ]