User manual SONY KP-46WT500

[. . . ] 01COV. book Page 2 Tuesday, July 30, 2002 3:46 PM WARNING To prevent fire or shock hazard, do not expose the projection TV to rain or moisture. Note on Caption Vision This television receiver provides display of television closed captioning in accordance with §15. 119 of the FCC rules. Note on convergence adjustment CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN Before you use your projection TV, make sure to adjust convergence. For details, see "Adjusting the Convergence Automatically ­ FLASH FOCUSTM ­" on page 33. ATTENTION RISQUE DE CHOC ELECTRIQUE, NE PAS OUVRIR Note to CATV system installer This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical. Use of this television receiver for other than private viewing of programs broadcast on UHF, VHF, transmitted by cable companies or satellite for the use of the general public may require authorization from the broadcaster/cable company and/or program owner. PRECAUCION RIESGO DE CHOQUE ELECTRICO NO ABRIR CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. [. . . ] The following will explain the function of some of the buttons found on your remote control. Buttons for Projection TV Operations 1 TV (FUNCTION) Using the Features Activates the remote control for use with the projection TV. 2 ANT-- (AUX input) Press to change between the VHF/UHF input and the AUX input. 3 TV (POWER) Turns the projection TV on and off. If a video input indication (e. g. , VIDEO 1, VIDEO 2) appears on the screen, press TV/VIDEO or CH +/ ­ until a channel number appears. 4 0-9 and ENTER Use for direct channel selection. Press 0-9 to select a channel (for example, to select channel 10, press 1 and 0). The channel will change after 2 seconds, or you can press ENTER for immediate selection. 5 CH +/­ Press to scan through the channels (+ up or ­ down). 6 VOL +/­ Press to adjust the volume (+ up or ­ down). 7 JUMP Press to alternate or jump back and forth between two channels. The projection TV will jump between the current channel and the last channel selected. 8 MUTING Press to mute the sound. "MUTING" will appear on the screen and will dim three seconds later. To restore the sound, press again or press VOL +. 9 FREEZE -- (yellow labeled button) This is useful when you need to copy down information that appears on the TV's screen (see "Using the Freeze Function" on page 44). q; SLEEP Press repeatedly until the projection TV displays the approximate time in minutes (15, 30, 45, 60, or 90) that you want the projection TV to remain on before shutting off automatically. Cancel by pressing SLEEP until "SLEEP OFF" appears or turning the power off. (Continued) 37 Model name1[KP-46WT500] Model name2[KP-51WS500] Model name3[KP-57WS500] Model name4[KP-65WS500] [4-088-847-12] 01COV. book Page 38 Tuesday, July 30, 2002 3:46 PM Using the Features qa DISPLAY Press to display the channel number, current time and channel label (if set). To turn the display off, press DISPLAY again. qs TV/VIDEO Press repeatedly to scroll through available video inputs: TV, VIDEO 1, VIDEO 2, VIDEO 3, VIDEO 4, VIDEO 5 VIDEO 6, and VIDEO 7. If you select Skip as a Video Label in the Setup menu, your projection TV will skip the video input you selected (see "Video Label" on page 59). qd MTS/SAP Press to scroll through the Multi-channel TV Sound (MTS) options (see "MTS" on page 51). qf PIC MODE Press PIC MODE repeatedly to directly choose one of four different video modes that best suits the program you are watching. Vivid: Select for enhanced picture contrast and sharpness. Standard: Select to display a standard picture for normal viewing environments. Movie: Select to display a finely detailed picture for low light environments. Pro (Professional): Select to display a picture with minimum enhancements. When you select each mode, you can also adjust the picture quality (such as Brightness, Color, etc. ) to suit your taste. For details, see "Mode" on page 49. 38 Model name1[KP-46WT500] Model name2[KP-51WS500] Model name3[KP-57WS500] Model name4[KP-65WS500] [4-088-847-12] 01COV. book Page 39 Tuesday, July 30, 2002 3:46 PM Using the Features Watching the Digital TV When you have connected the DTV receiver, you can enjoy digital TV programs. This projection TV is capable of receiving the 1080i, 720p, 480p and 480i digital TV formats. This projection TV is not capable of displaying a native 720p format signal. When a 720p format signal is received, it is converted into a 480p format signal. Using the Features To view a digital TV program 1 2 3 4 Connect the DTV receiver to VIDEO 5, 6 or 7 IN on the projection TV. (for details, see page 28) Press TV/VIDEO to select VIDEO 5, 6 or 7. Select a digital channel on the DTV receiver. For details, see the Operating Manual of the DTV receiver. Adjust the volume of the projection TV as necessary. 39 Model name1[KP-46WT500] Model name2[KP-51WS500] Model name3[KP-57WS500] Model name4[KP-65WS500] [4-088-847-12] 01COV. book Page 40 Tuesday, July 30, 2002 3:46 PM Using the Features Using Favorite Channels The Favorite Channel feature lets you select programs from a list of favorite channels that you preset. To display a list of your favorite channels: Your Favorite Channel options can be set automatically or manually. The factory setting for Favorite Channel is Auto. When Favorite Channel is set to Auto, the last eight channels selected with 0-9 buttons will be set as Favorite Channel options. [. . . ] Make sure Cable is set to ON in the Channel menu (see "Cable" on page 53). Use Auto Program in the Channel menu to add receivable TV channels that are not presently in TV memory (see page 54). Use Auto Program in the Channel menu to add receivable TV channels that are not presently in TV memory (see page 54). In the password screen (see page 60), enter the following master password: 4357. [. . . ]