User manual SONY KV-20FS100

[. . . ] Connecting Additional Equipment 4-086-340-21 Operating Instructions KV-13FS100 KV-13FS110 KV-20FS100 KV-24FS100 © 2002 by Sony Corporation User Guide Connecting Additional Equipment WARNING To reduce the risk of fire or electric shock, do not expose the TV to rain or moisture. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN ATTENTION RISQUE DE CHOC ELECTRIQUE, NE PAS OUVRIR PRECAUCION RIESGO DE CHOQUE ELECTRICO NO ABRIR CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. Note to the CATV Installer This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building as close to the point of cable entry as practical. SAFETY PRECAUTIONS Operate the TV only on 120 V AC. One blade of the power plug is wider than the other for safety purposes and will fit into the power outlet only one way. [. . . ] If so, connect the cables to like colors. Connecting Your TV Connecting a Camcorder Using Audio/Video cables (not supplied), connect AUDIO and VIDEO OUT on your camcorder to AUDIO and VIDEO IN on your TV. Front A/V Panel F F A/V output Audio R (red) Audio L (white) Video (yellow) Connecting Headphones Connect the headphones to the jack on the front of your TV. Front A/V Panel 11 Operating Instructions Using the Remote Control and Basic Functions This section shows you how to use the buttons on the remote control and how to navigate the on-screen menus. 1 2 3 MUTING SLEEP POWER 8 9 0 MTS/SAP DISPLAY TV/VIDEO 1 4 7 JUMP 2 5 8 0 CH 3 6 qz 9 ENTER 4 VOL 5 RESET MENU qs 6 7 RM-Y173 qd TV 12 Using the Remote Control and Basic Functions Using the Remote Control Button 1 MUTING 2 SLEEP 3 MTS/SAP 4 JUMP Description Instantly turns off the sound. to restore Turns the TV off automatically in approximately 15, 30, 45, 60, or 90 minutes. Cancel by pressing until SLEEP OFF appears. Cycles through the Multi-channel TV Sound (MTS) options: Stereo, Mono, and Auto SAP (Second Audio Program). Press to jump back and forth between two channels. The TV alternates between current channel and the last channel that was selected. Press when you want to adjust the volume. Press to return to factory settings while in an on-screen menu. Moves the cursor in the on-screen menus. Press the arrow buttons to move the cursor, then press the center button to select or access an option. Press when you want to turn the TV on or off. Press to display the current time (if set) and channel number. Press channel, then press ENTER. 0 9 5 VOL (volume) 6 RESET 7 8 POWER 9 TV/VIDEO 0 DISPLAY qa 0 9 and ENTER buttons to select a qs CH (channel) qd MENU Press when you want to change channels. Press again to exit the menu at any time. If you lose your remote control, see page 32. 13 Operating Instructions Setting Up the TV Automatically After you have finished connecting your TV, you can perform Auto Program to set up your channels. 1 Press to turn on the TV. The Initial Setup screen appears. Initial Setup First please connect cable / antenna Auto Program Exit [CH+] [CH­] 2 Press press on the remote control or on the TV front panel to perform Auto Program, or to exit. To perform Auto Program again 1 2 3 4 5 14 The Initial Setup screen appears each time you turn on the TV until you perform Auto Program. Press . to exit. Press g to highlight Channel Setup ( Press f to highlight Cable. Press Press F or f to select On or Off according to how you connected your TV. Press Press f to highlight Auto Program. Press After performing Auto Program, press Using the Remote Control and Basic Functions Quick Start to the Menus The following settings are available in your on-screen menus: Menu Allows you to Make adjustments to your picture settings. Video Picture Controls Color Temp. : Neutral VM : Low Move Select End Change your audio settings. Audio MTS : Stereo Move Select End Customize your channel settings. Channel Setup Favorite Channels Cable : On Channel Fix : Off Auto Program Channel Skip/Add Channel Label Move Select End Set rating limits on your TV based on a program's rating or content. Parental Control Password : Move Select End The menus shown in this manual are for KV-24FS100. Your menus may not look like those illustrated. 15 Operating Instructions Menu Allows you to Set the clock on your TV and program scheduled viewing using Timer 1 and Timer 2. Timer Timer 1 : Set Timer 2 : Set Current Time Move Select End Setup Caption Vision : Off Video Label Tilt Correction Language : English Demo Move Select End Select closed captioning options, label video inputs, adjust tilt correction, select menu languages, or run a demo of the menus. 16 Using the Menus 2Using the Menus This section shows the options available for setting up and adjusting your TV. To Access a Menu 1 2 3 4 5 Press to display the on-screen menu. [. . . ] Check the antenna and/or cable connections (page 4). Press so that MUTING disappears from the screen (page 13). Your TV may be set to Auto SAP (page 19). Adjust Color in the Picture Controls menu under Video (page 18). [. . . ]