User manual SONY KV-27TS29

[. . . ] If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: PRECAUCION RIESGO DE CHOQUE ELECTRICO NO ABRIR CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. Reorient or relocate the receiving antennas. Increase the separation between the equipment and receiver. [. . . ] Connect a coaxial cable (not supplied) from the OUT jack on your cable box to the VHF/UHF jack on the TV. Optional Connection To view channels from your cable box, tune your TV to channel 3 or 4 (as set on the rear panel of your cable box) and use the cable box's remote control to change channels. If you will be controlling all channel selection through your cable box, you should consider using the Channel Fix feature by setting your TV to channnel 3 or 4 (see page 22). 8 TV, VCR, and Cable Box Rear of TV 3 VCR Connections 2 Cable Box 1 From cable Optional connection Video (yellow) Audio L (white) Audio R (red) 1 2 3 Connect the coaxial cable from your cable service to the IN jack on your cable box. Connect a coaxial cable (not supplied) from the OUT jack on your cable box to the IN jack on your VCR. Connect a coaxial cable (not supplied) from the OUT jack on your VCR to the VHF/UHF jack on the TV. If you will be controlling all channel selection through your cable box, you should consider using the Channel Fix feature by setting your TV to channel 3 or 4 (see page 22). Optional connection If your VCR is equipped with video outputs, you can get better picture quality by connecting Audio/Video cables (not supplied) from Audio and Video OUT on your VCR to Audio/Video IN on your TV. For better picture quality, use S VIDEO instead of the yellow Audio/ Video cable. S-VIDEO does not provide sound; the audio cables must still be connected. S-VIDEO is only for KV-24FS120 model. You can use the button to switch between the VHF/UHF and VIDEO inputs. 9 TV and Satellite Receiver From cable/ antenna Rear of TV 2 1 Satellite Receiver Connections Satellite antenna cable Video (yellow) Audio L (white) Audio R (red) 3 1 2 3 Connect the cable from your satellite antenna to SATELLITE IN on your satellite receiver. Connect the coaxial cable from your cable service or antenna to the VHF/UHF jack on your TV. Using audio/video cables (not supplied), connect AUDIO and VIDEO OUT on your satellite receiver to AUDIO and VIDEO IN on your TV. To watch video programs from your Satellite receiver, tune your TV to channel 3 or 4. Optional Connection For better picture quality, use S VIDEO instead of the yellow audio/video cable. S-VIDEO does not provide sound; the audio cables must still be connected. S-VIDEO is only for KV-24FS120 model. You can use the button to switch between the VHF/UHF and VIDEO inputs. 10 TV, Satellite Receiver, and VCR Satellite antenna cable 4 From cable/ antenna Rear of TV 1 VCR 2 Connections Satellite Receiver 3 5 Video (yellow) Audio L (white) Audio R (red) 1 2 3 4 5 Connect the cable from your satellite antenna to SATELLITE IN on the satellite receiver. to select it. Use the G or g buttons to highlight the desired menu icon. Press Use the F or f buttons to scroll up and down through the features. Follow the instructions on the screen. For instructions on using a specific menu, see the page in this section that talks about that menu. Press to exit the menu. Press once to display the on-screen menu, and press again to return to normal viewing. If no buttons are pressed, the menu closes automatically after about 90 seconds. 19 Using the Video To Display To Select Menu Picture Controls Menu Video : Vivid Picture Brightness Color Hue Sharpness To access the Video menu, refer to the following steps: Video Mode : Vivid Picture Controls Color Temp: Cool VM : High Move Select End Return Select End Press f to highlight an option, then Mode Customized picture viewing . Use the F or f buttons to highlight one of the following options, then press to select it. Vivid: Select for enhanced picture contrast and sharpness. Standard: Select for a standard picture. Movie: Select for a finely detailed picture. Pro: Select for natural picture and sharpness. on the remote control for direct access to the picture modes (Vivid, Standard, Movie, Pro). Press Picture Control With the Picture Controls menu open, press F or f to select one of the following option: Picture: Press G to decrease the contrast. Brightness: Press G to darken the picture. Color: Press G to decrease color saturation. [. . . ] Contact your nearest Sony Dealer to order a replacement, please call our Sony Direct Accessory and Part Center at 1-800-488-7669 (U. S. residents only). Video Problem No picture, no sound Possible Remedies Make sure the power cord is plugged in. If a red light is flashing on the front of your TV for more than a few minutes, disconnect and reconnect the power cord. If the problem continues, call your local service center. [. . . ]