User manual SONY KV-27V22

[. . . ] If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ATTENTION RISQUE DE CHOC ELECTRIQUE, NE PAS OUVRIR PRECAUCION RIESGO DE CHOQUE ELECTRICO NO ABRIR CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. Reorient or relocate the receiving antennas. Increase the separation between the equipment and receiver. [. . . ] To scan quickly through channels, press and hold down either CH button. SETUP qf SLEEP qg 0 - 9 ENTER qh FAVORITES qj MTS/SAP Setup Remote Control qk FREEZE ql w; MENU wa CH +/- SETUP ws MEMORY STICK Press to display the Memory Stick Menu. For details, see "Using the Memory Stick Picture Viewer" on page 51. wd AV 1 2 3 DVD Use the A/V slide switch to control connected video equipment. You can program one video source for each switch position. For details, see "Programming the Remote Control" on page 43. SETUP SETUP 41 Inside Panel To access the inside panel, open the outside cover as shown. Button Description SETUP wf TV/VIDEO wg TV/VCR wh DISPLAY MUTING VCR/DVD SAT/CABLE POWER TV TV/VIDEO TV/VCR FUNCTION VCR/DVD SAT/CABLE DISPLAY GUIDE TV SYSTEM OFF REC DISC MENU DVD TITLE MENU RESET PIC MODE SLEEP DRC MODE FREEZE FAVORITES MTS/SAP VOL MENU CH Setup MEMORY STICK CODE SET AV 1 2 3 DVD RM -Y186 wj DISC MENU wk DVD TITLE wl RESET TV e; FUNCTION Buttons Press repeatedly to cycle through the video equipment connected to the TV's video inputs. Press to change the VHF/UHF output of the VCR. Press once to display the current channel number and current time and channel label (if set). Press to reset the settings to the factory defaults. Also used to clear Favorite Channels (see page 49). The indicator lights up momentarily when pressed to show which equipment the remote control is operating: VCR/DVD: Press to have the remote control operate the VCR or DVD player. SAT/CABLE: Press to have the remote control operate the satellite receiver or cable box. Switch the TV's input to the VCR, DVD player, or other connected equipment Press TV/VIDEO repeatedly to cycle through the video equipment connected to the TV's video inputs. Press MENU to display the Menu. For Change video and audio details, see "Using the Menus" on options, customize the TV's setup, set parental controls, and page 61. more Switch the TV's input between sources connected to the TV's VHF/UHF and AUX inputs Press ANT to alternate between sources connected to the TV's VHF/UHF and AUX inputs. 45 Using Twin View Twin View lets you see two pictures from two sources -- from an antenna, VCR, DVD, etc. , -- on the screen at the same time. You hear the sound from only one of the sources at a time, but you can choose which source's sound is selected. You can also change the relative size of each of the pictures. SETUP SETUP Displaying Twin Pictures 1 Tune the TV to a working channel. The active picture is highlighted in blue. , SETUP To cancel Twin View and watch the active picture Press or . Features Factors Affecting Twin View If you use a cable box to view all channels, the same channel appears in both windows of Twin View because the cable box unscrambles only one channel at a time. If you use a cable box, you can view the cable box output in one Twin View window and view a different source (such as a VCR or DVD player) in the second window by using the TV/VIDEO button. For details, see "Connecting Optional Equipment" on page 21. Sources connected to the AUX, VIDEO 5, VIDEO 6, and VIDEO 7 inputs display in the left Twin View window, but not the right. If you are viewing a 4:3 source and a 16:9 enhanced source (such as a DVD) side by side in Twin View, the 4:3 source appears larger. SETUP SETUP 46 , Activating the Picture To activate the picture in the right window Move the joystick b. To activate the picture in the left window Move the joystick B. SETUP , , Functions Available in the Active (Highlighted) Window To Do This . . . Do This . . . SETUP Tune to a channel Press 0-9 and then ENTER (or wait 3 seconds) or Press CH+/Press VOL +/Press MUTING (press again to unmute) Press ANT (left window only) SETUP Adjust the volume Mute the volume Switch the TV's input between sources connected to the TV's VHF/UHF and AUX inputs Switch the TV's input between sources connected to the TV's A/V inputs Change the picture size Press TV/VIDEO Features SETUP SETUP Move the joystick V or v. [. . . ] If already set to Stereo, switch to Mono (which may reduce background noise during weak stereo broadcasts). If the Speaker option is set to Off and the Audio Out option is set to Fixed (in order to output the sound to your audio system) use your audio receiver to adjust the sound (see page 64). Or, to use the TV remote control, set the Audio Out option to Variable. To turn on the TV speakers, set the Speaker option to On (see page 64). SETUP 80 Channels Welcome Problem Possible Remedies Cannot receive upper channels (UHF) when using an antenna TV is fixed to one channel Cannot receive any channels when using cable TV Cannot receive or select channels Change the Cable option to Off (see page 66). [. . . ]