User manual SONY KV-28FS20U

[. . . ] This Instruction Manual has been produced using Totally chlorine free (TCF) 100% Re-cycled paper to comply with our commitment to the use of environmentally friendly materials in our products. A moulded plug complying with BS1363 is fitted to this equipment for your safety and convenience. Should the fuse in the plug supplied need to be replaced, a 5 AMP fuse approved by ASTA or BSI to BS 1362 (i. When an alternative type of plug is used it should be fitted with a 5 AMP FUSE, otherwise the circuit should be protected by a 5 AMP FUSE at the distribution board. [. . . ] Repeat steps 4 and 5 if you wish to sort other channels. Although the picture is adjusted at the factory, you can modify it to suit your own taste. Press the V or v buttons on the remote control to select the symbol on the menu screen then press the b button to enter the `PICTURE CONTROL' menu. Press the V or v buttons to select the item on the screen you wish to adjust then press the b button to confirm. If you selected `Picture Mode' or `Format' in step 3, press the V or v buttons to select the item on the screen you wish to adjust then press the b button to confirm. As soon as you have adjusted the item, press the OK button to store the new setting. If you selected `Picture Mode' or `Format' in step 3, press the B button to return to the `PICTURE CONTROL' menu. Repeat steps 3-7 to adjust the other items. Brightness* Colour* Sharpness* Hue** Contrast Reset Format Format Scroll Auto 16:9 Resets picture to factory preset levels (refer to page 15 for details) b Off B On Changing picture and sound modes quickly You can quickly change the Picture Mode or the Sound Mode without entering the `PICTURE CONTROL' or the `SOUND CONTROL' menu screens. Press the symbol on the remote control for picture modes or the symbol for sound modes. Although the sound is adjusted at the factory, you can modify it to suit your own taste. Press the V or v buttons on the remote control to select the symbol on the menu screen then press the b button to enter the `SOUND CONTROL' menu. Press the V or v buttons to select the item on the screen you wish to adjust then press the b button to confirm. If you select `Sound Mode' or `Surround Mode' in step 3, press the V or v buttons to select the item on the screen you wish to adjust then press the b button to confirm. As soon as you have adjusted the item, press the OK button to store the new setting. If you selected `Sound Mode' or `Surround Mode' in step 3, press the B button to return to the `SOUND CONTROL' menu. Repeat steps 3-7 to adjust the other items. Balance Only available when `Surround Mode' is set to `Off' Reset Resets sound to factory preset levels Boosts bass by a fixed amount Choose from the special sound effects: Pro Logic--> Pseudo Stereo--> Spatial--> off Before listening to Dolby Pro Logic encoded programmes, you can adapt the Dolby features to suit your own taste. Normally this is only required when you install the TV and the speakers, or when changing the speaker positions. Press the V or v buttons to select the symbol on the menu screen then press the b button to enter the `PRESET' menu. Press the V or v buttons to select `Dolby Pro Logic Setup' on the menu screen then press the b button to enter the `DOLBY PRO LOGIC SETUP' menu. Press the b or B buttons to select one of the following modes then press the OK button to store the chosen mode: Dolby Pro Logic: all 5 speakers are activated Dolby 3 stereo: surround speakers are not used Press the b or B buttons to select one of the following modes then press the OK button to store the chosen mode: Normal: all 5 speakers are activated Wide: wider bandwidth for centre speaker Phantom: centre speaker is not used 6. [. . . ] Connecting to external audio equipment Plug in your hi-fi equipment to the E sockets on the rear of the TV if you wish to amplify the audio output from the TV. The output level from the E sockets can be varied by adjusting the volume of the headphones (refer to the `Adjusting the sound' section of this manual). For mono equipment Connect the phono plug to the L/G/S/I socket on the front of the TV and select the 3 input signal using the instructions on this page. Finally, refer to the `Adjusting the sound' section of this manual and select `A' on the sound menu screen. [. . . ]