User manual SONY KV-32FS10

[. . . ] If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ATTENTION RISQUE DE CHOC ELECTRIQUE, NE PAS OUVRIR PRECAUCION RIESGO DE CHOQUE ELECTRICO NO ABRIR CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. Reorient or relocate the receiving antennas. Increase the separation between the equipment and receiver. [. . . ] Using audio/video cables (not supplied), connect AUDIO/VIDEO OUT on your satellite receiver to AUDIO/VIDEO IN on your TV. To view from the satellite receiver or VCR, select the video input to which your satellite receiver or VCR is connected by pressing on the remote control. 4 5 6 12 Connecting a TV, VCR, and Satellite Receiver using Component Video (YPBPR) Rear of TV 4 1 Satellite receiver Y VIDEO 1 From 2 cable/ 1 S VIDEO 3 4 Y antenna VIDEO L (MONO) PB AUDIO OUT (VAR/FIX) PR VCR LINE IN VIDEO AUDIO L AUDIO R LINE OUT L L (MONO) 3 Video (yellow) Audio L (white) Audio R (red) R R R Connections PB L PR R R L Y (green) PB (blue) PR (red) 6 7 Audio R (red) Audio L (white) 5 1 2 3 4 5 6 7 Connect the coaxial cable from your satellite antenna to SATELLITE IN on the satellite receiver. Connect the coaxial cable from your cable service or antenna to the IN jack on your VCR. Using a coaxial cables (not supplied), connect the OUT jack on your VCR to the VHF/UHF jack on your TV. Using audio/video cables (not supplied), connect AUDIO/VIDEO OUT on your satellite receiver to AUDIO/VIDEO IN on your VCR. Using audio/video cables (not supplied), connect AUDIO/VIDEO OUT on your VCR to AUDIO/VIDEO IN on your TV. Using component video cables (not supplied), connect YPBPR OUT on your satellite receiver to YPBPR IN on your TV. Connect AUDIO OUT on your satellite receiver to AUDIO IN on your TV. To view from the satellite receiver or VCR, select the video input to which your satellite receiver or VCR is connected by pressing on the remote control. 13 Connecting a DVD Player using Composite Video (VIDEO/AUDIO L(MONO), R) Using audio/video cables (not supplied), connect AUDIO/VIDEO OUT on your DVD player to AUDIO/VIDEO IN on your TV. Rear of TV Rear of DVD Player 1 S VIDEO Y 3 4 PB AUDIO OUT (VAR/FIX) PR VIDEO L (MONO) L L (MONO) R R R Connections Optional connection Video (yellow) Audio L (white) Audio R (red) Optional connection For better picture quality, use S VIDEO instead of the yellow video cable. S VIDEO does not provide sound, so you still must connect the audio cables. Connecting a DVD Player using Component Video (YPBPR/R, L) If your DVD player is equipped with component video outputs (YPBPR), you can improve the picture quality by using component video cables (480i only). Rear of TV Rear of DVD Player 1 S VIDEO Y 3 4 PB AUDIO OUT (VAR/FIX) PR VIDEO L (MONO) L L (MONO) R R R PR (red) PB (blue) Y (green) 2 1 Audio L (white) Audio R (red) 1 2 Make sure your DVD player is set up (see page 35). Using component video cables (not supplied), connect YPBPR OUT on your DVD player to YPBPR IN on your TV. Menu Allows you to Video Mode:Vivid Picture Brightness Color Hue Sharpness Col o r Temp:Cool ClearEdge VM:High Move Select End Adjust your picture settings. Basic Functions Audio Treble Bass Balance Steady Sound:Off Effect:Off MTS:Stereo Speaker:On Audio Out:Fixed Move Select End Change your audio settings. Channel Setup Favorite Channels Cable:On Channel Fix:Off Auto Program Channel Skip/Add Channel Label Move Select End Customize your channel settings. Parental Control Password: Move Select End Set rating limits on your TV based on program rating or content. 18 Menu Allows you to Timer Timer 1:Set Timer 2:Set Current Time Move Select End Set the clock on your TV and program scheduled viewing using Timer 1 and Timer 2. Setup Caption Vision:Off Info Banner:Off Video Label Tilt Correction Language:English 16:9 Enhanced:Off Move Select End Select closed captioning options (Caption Vision), display the name of the current program and its remaining time (Info Banner), label video inputs, adjust tilt correction, select menu language, enhance DVD picture resolution (16:9 Enhanced). Basic Functions 19 Using the Menus This section shows the options available for setting up and adjusting the TV. Using the Remote Control to Navigate the On-Screen Menus JUMP PICTURE MODE 0 VOL ENT CH Move MENU Select RESET SLEEP RM-Y194 To navigate on the on-screen menus, use the arrow buttons (V , v , B, b) to move the cursor. Pressing these arrows will cause the cursor to move in the corresponding direction. Press the center button ( ) to select an option. How to Access Menus Menus To Access Menus 1 2 3 4 5 6 Press to display the on-screen menu. to select it. Use the B or b buttons to highlight the desired menu icon. Press Use the V or v buttons to scroll up and down through the features. Follow the instructions on the screen. For instructions on using a specific menu, see the page in this section that talks about that menu. Press to exit the menu. Press once to display the on-screen menu, and press again to return to normal viewing. If no buttons are pressed, the menu closes automatically after about 90 seconds. 21 Using the Video Menu To access the Video menu, use the following steps: To Display To Select Press v to highlight an option, then press Mode Customized picture viewing . Video Mode:Vivid Picture Brightness Color Hue Sharpness Col o r Temp:Cool ClearEdge VM:High Move Select End Use the V or v buttons to highlight one of the following options, then press to select it. Vivid: Select for enhanced picture contrast and sharpness. Standard: Select for a standard picture. [. . . ] If the problem continues, call your local service center. When watching TV, set it to TV; when watching video equipment, set it to VIDEO 1, 2, 3 or 4 (page 4). Make sure you have inserted the batteries correctly into the remote control (page 2). Try another channel to rule out station trouble. [. . . ]