User manual SONY KV-32V26

[. . . ] If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. Note to the CATV Installer This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building as close to the point of cable entry as practical. Reorient or relocate the receiving antennas. Increase the separation between the equipment and receiver. [. . . ] Using coaxial cables (not supplied), connect the two output jacks of the splitter to: a) the IN jack on your cable box b) the VHF/UHF jack on the TV 3 4 Using a coaxial cable (not supplied), connect the OUT jack on your cable box to the IN jack on your VCR. If your VCR is equipped with video outputs, you can get better picture quality by connecting audio/video cables (not supplied) from AUDIO/VIDEO OUT on your VCR to AUDIO/VIDEO IN on your TV. (continued) 15 Operating Instructions DIGITAL CABLE BOX USERS: Do not use this connection. The TO CONVERTER jack is not compatible with digital boxes. Optional connection For better picture quality, use S VIDEO instead of the yellow video cable. S VIDEO does not provide sound, so you still must connect the audio cables. Using your TV with this connection Program your Sony remote control to operate your VCR or cable box (see page 5). To activate your remote, press to operate your VCR or to operate your cable box. To do this, first program your remote control, then use the Channel Fix feature to set your TV to channel 3 or 4 (see page 31). Press repeatedly to switch between VCR input (VIDEO input), VHF/UHF (local channels or unscrambled), or cable box (cable system or scrambled channels). 16 Connecting Your TV Connecting a TV and Satellite Receiver From cable/ antenna 2 1 Rear of TV 3 4 Y 5 AUDIO OUT (VAR/FIX) S VIDEO 1 Satellite antenna cable Satellite receiver VIDEO L (MONO) PB PR L (MONO) R R 3 Video (yellow) Audio L (white) Audio R (red) 1 2 3 Connect the cable from your satellite antenna to SATELLITE IN on your satellite receiver. Connect the coaxial cable from your cable service or antenna to the VHF/UHF jack on your TV. Using audio/video cables (not supplied), connect AUDIO/VIDEO OUT on your satellite receiver to AUDIO/VIDEO IN on your TV. Using your TV with this connection This connection allows you to do the following: Program your Sony remote control to operate your satellite receiver (see page 5). To activate your remote, press to operate your satellite receiver. Perform Auto Program again to program receivable channels. Press to turn on the TV. The Initial Setup screen appears. Initial Setup Auto Program: [CH+] [CH­] Exit: First please connect cable/antenna 2 Press on the remote control or on the TV front panel to start Auto Program, or press to exit. The Initial Setup screen appears each time you turn on the TV until you perform Auto Program. 1 2 3 4 5 6 1 2 3 4 To perform Auto Program again Press . Press Press F or f to highlight On or Off according to how you connected your TV. Press After Auto Program finishes, press to search for channels. to exit. To reset the TV to factory settings Turn the TV on. Press and release the POWER button on the TV front panel. The TV will turn itself off, then back on. Release . 21 Operating Instructions Quick Start to the Menus The following settings are available in your on-screen menus. For more details on how to use the menus, see "Using the Menus" on page 27. Menu Video Audio Channel Parent Timer Setup Basic Allows you to Mode : Vivid Picture Brightness Color Hue Sharpness Color Temp. : Cool VM: High Move: Select: End: Adjust your picture settings. Video Audio Channel Parent Timer Setup Basic Treble Bass Balance Effect: Off MTS: Stereo Speaker: On Audio Out: Variable Move: Select: End: Change your audio settings. Video Audio Channel Parent Timer Setup Basic Favorite Channels Cable : On Channel Fix: Off Auto Program Channel Skip/Add Channel Label Move: Video Audio Select: Channel Parent Timer End: Setup Basic Customize your channel settings. Password: Move: Select: End: Set rating limits on your TV based on program rating or content. 22 Using Basic Functions Menu Video Audio Channel Parent Timer Setup Basic Allows you to Timer 1 : Off Timer 2 : Off Current Time : Move: Select: End: AM Set the clock on your TV and program scheduled viewing using Timer 1 and Timer 2. Video Audio Channel Parent Timer Setup Basic Caption Vision: Off Video Label Tilt Correction: 0 Language: English 16:9 Enhanced: Off Demo Move: Video Audio Select: Channel Parent Timer End: Setup Basic Select closed captioning options, label video inputs, adjust tilt correction, enhance your DVD picture resolution (16:9 Enhanced), select menu language, or run a demo of the menus. Press to enter Basic Menu Move: Select: End: Basic Menu Picture Caption Vision: Off Effect: Off Advanced Menu Picture white level Move: Select: End: Adjust Access the most commonly used menu settings. 23 Operating Instructions Using Picture in Picture (PIP) The Picture-in-Picture (PIP) feature allows you to view two programs simultaneously, one in the full size "main" picture and one in a small "window" picture. Displaying Picture in Picture Indicates which picture is currently receiving sound Main picture 9 6 2 Channel number of the main picture Channel number of the window picture Window picture To use PIP 1 2 3 1 2 3 4 5 Press the TV button to control PIP with the yellow buttons. Tune your TV to a channel that you know is currently airing programming. [. . . ] Check the antenna and/or cable connections (page 11). Make sure the channel selected is currently broadcasting. Move the TV away from other electronic equipment. Some electronic equipment creates electrical noise, which can interfere with TV reception. [. . . ]