User manual SONY KV-9PT60

[. . . ] If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ATTENTION RISQUE DE CHOC ELECTRIQUE, NE PAS OUVRIR PRECAUCION RIESGO DE CHOQUE ELECTRICO NO ABRIR CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. Reorient or relocate the receiving antennas. Increase the separation between the equipment and receiver. [. . . ] Change the PIP channel via the cable box. (The cable box's tuner is used as the PIP video source; if you do not turn on the cable box, the PIP will not work. ) This system is needed because the cable box unscrambles only one channel at a time (unlike regular cable, which makes all channels available concurrently). 19 Installing the TV Connecting Two VCRs for Tape Editing If you connect two VCR's together, so you can record from one to the other, you may want to monitor the recording process. You can connect the recording VCR into your TV and then view what is being recorded. The procedure below shows you how to do this. 1 Using an A/V cable, connect the playback VCR's Audio and Video OUT jacks to the recording VCR's Audio and Video IN jacks. 2 Using an A/V cable, connect the recording VCR's Audio and Video OUT jacks to the TV's Audio and Video IN jacks. TV VCR (playback) VCR (recording) AUDIO-R (red) AUDIO-L (white) VIDEO (yellow) A/V cable A/V cable To change the video input of the VCR. See your VCR's user's guide for instructions. To view what is being recorded Use the remote control to set the TV to the video input to which the recording VCR is connected. (VIDEO 1 in the illustration above. ) If the VCRs you are connecting have S VIDEO jacks, you can use S VIDEO cables to improve picture quality; replace the yellow video cable of the combination A/V cable with the S VIDEO cable. You will still need audio cables for sound. 20 Installing the TV Connecting a Satellite Receiver 1 Connect the satellite antenna cable to the satellite receiver's SATELLITE IN jack. 2 Using an A/V cable, connect the satellite receiver's Audio and Video OUT jacks to the TV's Audio and Video IN jacks. 3 Connect a coaxial cable from your cable or antenna to the TV's VHF/UHF jack. If the satellite receiver has an S VIDEO jack, you can use an S VIDEO cable to improve picture quality; replace the yellow video cable of the combination A/V cable with the S VIDEO cable. You will still need audio cables for sound. TV Coaxial cable Satellite antenna cable Satellite receiver AUDIO-R (red) AUDIO-L (white) VIDEO (yellow) A/V cable 21 Installing the TV Connecting a Satellite Receiver with a VCR 1 Connect the satellite antenna cable to the satellite receiver's SATELLITE IN jack. 2 Connect the CATV cable to the VCR's VHF/UHF IN jack. 3 Using a coaxial cable, connect the VCR's OUT jack to the TV's VHF/UHF jack. 4 Using an A/V cable, connect the satellite receiver's Audio and Video OUT jacks to the VCR's Audio and Video IN jacks. 5 Using an A/V cable, connect the VCR's Audio and Video OUT jacks to the TV's Audio and Video IN jacks. Satellite antenna cable Satellite receiver TV VCR CATV Coaxial cable AUDIO-R (red) AUDIO-L (white) VIDEO (yellow) Coaxial cable A/V cable If the satellite receiver and VCR have S VIDEO jacks, you can use an S VIDEO cable to improve picture quality; replace the yellow video cable of each combination A/V cable with the S VIDEO cable. You will still need audio cables for sound. 22 Installing the TV To change VCR video input See your VCR's user's guide for instructions. If this does not work, check "Troubleshooting" on page 54 for potential solutions. PIP Functions 1 2 3 4 5 6 7 Yellow-labeled PIP Button Description Freezes the window picture. The main window continues to play as usual. Changes the channel in the window picture. To change the channel in the main window, use the main CH+/buttons at the bottom of the remote control. Moves the location of the window picture among the four corners of the screen. Switches the main picture with the window picture. Press repeatedly to change the window size (1/9, 1/16, OFF). Cycles through available video equipment you have connected to the TV. Alternates sound between the main picture and the window picture. The sound symbol (9) appears for 3 seconds, indicating whether you are hearing sound from the main picture or the window picture. 1 FREEZE 2 CH +/- RM-Y181 remote control 3 POSITION 4 SWAP 5 PIP 6 TV/VIDEO 7 AUDIO 32 Using the Features To change channels/programs in the PIP window Use the yellow PIP CH+/- button to scroll through the TV channels. Use the yellow TV/VIDEO button to cycle through your other video equipment connected to the TV, such as your VCR, DVD player or Satellite Receiver. Setups that affect your ability to use PIP Any video equipment you have connected to the AUX input z Be sure to label your video sources to make them easier to find in the Display. See "Video Label" on page 47 for labeling instructions. cannot be viewed in the PIP window. If you are viewing all channels through a cable box, the PIP feature will not work. [. . . ] Increase the volume of the cable box using the cable box's remote control. Then press TV (FUNCTION) and adjust the TV's volume. 54 Other Information Problem Possible Remedies Cannot receive channels Unable to select a channel Lost password Cannot change channels with the remote control Cannot cycle through the other video equipment connected to the TV There is a black box on the screen Use Auto Program in the Channel menu to add receivable TV channels that are not presently in TV memory (see page 40). Use Auto Program in the Channel menu to add receivable TV channels that are not presently in TV memory (see page 40). In the password screen (see page 42), enter the following master password: 4357. [. . . ]