User manual SONY KV-1354R

[. . . ] Never use the plug without the fuse cover. If you should lose the fuse cover, please contact your nearest Sony service station. How to replace the fuse Open the fuse compartment with a blade screwdriver, and replace the fuse. · IMPORTANT If the plug supplied is not suitable for the socket outlets in your home, it should be cut off and an appropriate plug fitted in accordance with the following instructions: The wires in this mains lead are coloured in accordance with the following code: Blue Neutral Brown Live As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black. The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red. [. . . ] Press again to switch on TV from standby mode. To save energy we recommend switching off completely when TV is not in use. After 15 minutes without a signal and without any button being pressed, the TV switches automatically into standby mode. 3 6 9 Selecting input source Press repeatedly until the desired input symbol of the source appears on the TV screen. Back to the channel last watched Press to watch the last channel selected (watched for at least 5 seconds). Displaying the menu system Press to display the menu on the TV screen. Press again to remove the menu display from the TV screen. Menu selection ·When MENU is switched on: Scroll Up Scroll Down Previous menu or selection Next menu or selection OK confirms your selection ·When MENU is switched off: OK Shows a channel overview. Press or to select the channel and then, press again the OK button to watch the selected channel. Selecting Screen format Press to view programmes in 16:9 mode. Press again to return to 4:3 mode. K GB PROGR RM 887 S Besides TV functions, all coloured buttons as well as green symbols are also used for Teletext operation. For more details, please refer to ""Teletext" section of this instruction manual. Overview 5 Overview of TV Buttons Auto Start Up Button Volume control buttons Programme Up or Down Buttons (Select TV channels) Press on the mark on the front of the TV to reveal the front connectors. Selecting Input source Standby indicator On/Off switch Video Input jack Audio Input jack Headphone jack Inserting Batteries into the Remote Control Make sure to insert the supplied batteries using the correct polarities. Always remember you dispose of used batteries in an environmental friendly way. 6 Overview-Installation Connecting an Indoor Aerial (only for KV-1354R) For a better reception we recommend you connect an external aerial. Then press or to select the channel tuning ("C" for terrestrial channels or "S" for cable channels). After that, press the number buttons to enter directly the channel number of the TV Broadcast or the channel of the VCR signal. If you do not know the channel number, press or to search for it. When you tune the desired channel, press OK twice to store. OK Set Up Language Auto Tuning Programme Sorting Manual Programme Preset Advanced Features OK Set Up Language Auto Tuning Programme Sorting Manual Programme Preset Advanced Features Repeat all the above steps to tune and store more channels. Manual Programme Preset Programme: Channel: Label: AFT: Skip: Confirm 01 C 21 --TVE On No b)Normally the automatic fine tuning (AFT) is OK operating, however you can manually fine tune the TV to obtain a better picture reception in the case that the picture is distorted. To do that: while watching the channel (TV Broadcast) you wish to fine tune, select the AFT option and press . Next press or to adjust the fine tuning between -15 and +15. Finally press OK twice to store. GB c) Skip any unwanted programme numbers when they are selected with the PROGR +/buttons. To do that: Highlighting the Programme option, press the PROGR +/- button to select the programme number you want to skip. When the programme you want to skip appears on the screen, select the Skip option and press . Finally press OK twice to confirm and store. To cancel this function afterwards, select "No" instead of "Yes" in the step above. d) Label a channel using up to five characters. To do that: Highlighting the Programme option, press the PROGR +/- button to select the programme number with the channel you wish to name. When the programme you want to name appears on the screen, select the Label option and press . [. . . ] Also refer to your VCR instruction manual to find out how to find the output channel of your VCR. 8mm/Hi8/DVC camcorder C 1 2 "PlayStation"* AB VCR GB Decoder * "PlayStation" is a product of Sony Computer Entertainment, Inc. * "PlayStation" is a trademark of Sony Computer Entertainment, Inc. Using Optional Equipment 1 2 Connect your equipment to the designated TV socket, as indicated above. To watch the picture of the connected equipment, press the correct input symbol appears on the screen. Symbol 1 Input Signals · Audio / video input signal through the Scart connector C · RGB input signal through the Scart connector C. [. . . ]