User manual SONY KV-1997R

[. . . ] If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. Note to the CATV Installer This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building as close to the point of cable entry as practical. Reorient or relocate the receiving antennas. Increase the separation between the equipment and receiver. [. . . ] Using audio/video cables (not supplied), connect AUDIO and VIDEO OUT on your satellite receiver to AUDIO and VIDEO IN on your TV. You can use the button to switch between the VHF/UHF and VIDEO inputs. For better picture quality, use S VIDEO instead of the yellow audio/video cable. S VIDEO does not provide sound; you still must connect the audio cables. 16 Connecting Your TV Connecting a TV, Satellite Receiver, and VCR 4 1 From cable/ antenna Rear of TV 1 3 4 2 VCR Satellite Receiver 3 5 Video (yellow) Audio L (white) Audio R (red) 1 2 3 4 5 Connect the coaxial cable from your satellite antenna to SATELLITE IN on the satellite receiver. Connect the coaxial cable from your cable service or antenna to the IN jack on your VCR. Using a coaxial cable (not supplied), connect the OUT jack on your VCR to the VHF/UHF jack on your TV. Using audio/video cables (not supplied), connect AUDIO and VIDEO OUT on your satellite receiver to AUDIO and VIDEO IN on your VCR. Using audio/video cables (not supplied), connect AUDIO and VIDEO OUT on your VCR to AUDIO and VIDEO IN on your TV. To view from the satellite receiver or VCR, select the video input to which your satellite receiver or VCR is connected by pressing on the remote control. 17 Operating Instructions Connecting a DVD Player Using audio/video cables (not supplied), connect AUDIO and VIDEO OUT on your DVD player to AUDIO and VIDEO IN on your TV. Rear of TV Rear of DVD Player 1 3 4 MONITOR AUDIO OUT (VAR/FIX) Video (yellow) Audio L (white) Audio R (red) For better picture quality, use S VIDEO instead of the yellow Audio/Video cable. S VIDEO does not provide sound; you still must connect the audio cables. Optional connection If your DVD player is equipped with component video outputs (Y, PB, PR), you can improve the picture quality by using component video cables (480i only). Rear of TV Rear of DVD Player 1 3 4 MONITOR AUDIO OUT (VAR/FIX) Y (green) PB (blue) PR (red) Audio L (white) Audio R (red) 2 1 1 2 Using component video cables (not supplied), connect the Y, PB, PR OUT on your DVD player to Y, PB, PR IN on your TV. Connect AUDIO OUT on your DVD player to AUDIO IN on your TV. The Y, PB, PR outputs on your DVD player are sometimes labeled Y, CB, and CR or Y, B-Y, and R-Y. If so, connect the cables to like colors. 18 Connecting Your TV Connecting a Camcorder Using audio/video cables (not supplied), connect AUDIO and VIDEO OUT on your camcorder to AUDIO and VIDEO IN on your TV. Front A/V Panel S VIDEO Front A/V Panel Audio R (red) Audio L (white) Video (yellow) A/V output If the camcorder has an S VIDEO jack, you can use an S VIDEO cable to improve picture quality; replace the yellow video cable of the combination Audio/Video cable with the S VIDEO cable. You will still need audio cables for sound. Connecting an Audio System Using audio cables (not supplied), connect AUDIO OUT on your TV to one of the unused line inputs (e. g. Rear of TV 1 3 4 MONITOR AUDIO OUT (VAR/FIX) AUDIO-L (white) AUDIO-R (red) Line input Set your stereo to the selected line input. Press the PIP (yellow) button to switch the PIP window to other video inputs for other equipment that is connected to any of the VIDEO IN jacks of your TV. You should see a different picture in your PIP window for each piece of connected video equipment. Make sure the connected equipment is turned on and working when you perform this test. If the PIP feature does not work properly with the TV or the connected video equipment, refer to the troubleshooting section beginning on page 52. If you're having problems with PIP, refer to "Setups that Affect Your Ability to Use PIP" (page 28) or see Troubleshooting section (page 52) for possible solutions. 6 24 PIP Functions buttons For KV-27FV300 model Yellow labeled PIP button Description Press to turn the PIP feature on and off. Press repeatedly to change the window size (1/9, 1/16, Off). Press to cycle through the available video equipment you have connected to the TV (in the PIP window picture). Press to alternate sound between the main picture and the PIP window picture. The sound symbol appears for three seconds, indicating whether you are hearing the sound from the main or PIP window picture. Press to change the channel in the PIP window picture. To change the channel in the main window, use the main CH+/- buttons at the bottom of the remote control. Press to move the location of the window picture to any of the four corners of the screen. [. . . ] If you are using another device to control channels, be sure that you have pressed the FUNCTION button for that device. For example, if you're using your VCR to control channels, be sure to press the VCR/DVD FUNCTION buttons (page 3 for remote Y181, page 5 for remote Y182). If you use the button to close the Basic menu, only the Basic menu appears when you press again. To access the other menus, select the Advanced Menu option (page 47). [. . . ]