User manual SONY KV-20TX10

[. . . ] If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. Note to the CATV Installer This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building as close to the point of cable entry as practical. Reorient or relocate the receiving antennas. Increase the separation between the equipment and receiver. [. . . ] These AUDIO/VIDEO input jacks provide better picture quality than the VHF/UHF jack. 3 AUDIO L(MONO), R/ VIDEO 9 Operating Instructions Jack 4 Y, PB, PR/ L, R Description These inputs (Video 4) connect to the component video Y, PB, PR, and AUDIO L, R jacks on your DVD player or digital set-top box (480i only). This jack connects to the Audio input jacks on your audio equipment. You can listen to your TV's audio through your stereo system. 5 AUDIO OUT (VAR/FIX) L, R 10 Connecting Your TV Basic Connections TV with Cable, Indoor, or Outdoor Antenna Depending on the cable system available in your home, choose one of the connections below: Use this to connect the TV to a cable system or an antenna with a 75-ohm cable (usually built in to newer homes). (not supplied) Use this to connect the TV to a dipole antenna, also known as a "rabbit ears antenna" (usually found in older homes). This allows you to connect your TV to both a cable system and a dipole antenna, in order to view both cable and local channels. If you are connecting to an indoor or outdoor antenna, you may need to adjust the orientation of the antenna for the best reception. 11 Operating Instructions Connecting Additional Equipment Connecting a TV and VCR Rear of TV 1 3 Y 4 AUDIO OUT (VAR/FIX) 2 VCR 1 From cable/antenna S VIDEO PB PR VIDEO L (MONO) L L (MONO) R R R Video (yellow) Audio L (white) Audio R (red) Optional connection 1 2 Connect the coaxial cable from your TV antenna or cable service to the IN jack on your VCR. Connect a coaxial cable (not supplied) from the OUT jack on your VCR to the VHF/UHF jack on the TV. Using your TV with this connection This connection allows you to do the following: Program your Sony remote control to operate your VCR (see page 5). To activate your remote, press to operate your VCR. To do this, first program your remote control, then use the Channel Fix feature to set your TV to channel 3 or 4 (see page 27). Press repeatedly to switch between VCR input (VIDEO input) and VHF/UHF (local channels). Optional connection If your VCR is equipped with video outputs, you can get better picture quality by connecting audio/video cables (not supplied) from AUDIO/VIDEO OUT on your VCR to AUDIO/VIDEO IN on your TV. For better picture quality, use S VIDEO instead of the yellow video cable. S VIDEO does not provide sound, so you still must connect the audio cables. 12 Connecting Your TV TV and Cable Box Some cable TV systems use scrambled or encoded signals that require a cable box to view all channels. If you subscribe to that kind of cable service, use this connection. If some, but not all, of your channels are scrambled, consider using the cable box and cable connection (see page 12). Cable box 1 From cable/ antenna Rear of TV 1 S VIDEO 3 Y 4 AUDIO OUT (VAR/FIX) PB PR 2 VIDEO L (MONO) L (MONO) R R 1 2 Connect the coaxial cable from your cable service to the IN jack on your cable box. For more instructions, see "Using the Audio Menu" on page 25. Open the Audio Out option on the Audio Menu and select Fixed to control the volume through the connected audio system. For more instructions, see "Using the Audio Menu" on page 25. Rear of TV 1 S VIDEO PB 3 Y 4 AUDIO OUT (VAR/FIX) PR AUDIO-L (white) L L (MONO) VIDEO L (MONO) R R R AUDIO-R (red) Line input 17 Using Basic Functions Setting Up the TV After you have finished connecting your TV, you can use Auto Program to set up your channels. During Auto Program, the TV will automatically search for available channels and program receivable channels. 1 When you start Auto Program wait until it is finished; otherwise it will skip over channels that are available. Perform Auto Program again to program receivable channels. Press to turn on the TV. The Initial Setup screen appears. Initial Setup Auto Program: [CH+] [CH­] Exit: First please connect cable/antenna 2 Press on the remote control or on the TV front panel to start Auto Program, or press to exit. The Initial Setup screen appears each time you turn on the TV until you perform Auto Program. 1 2 3 4 5 6 1 2 3 4 To perform Auto Program again Press . Press Press F or f to highlight On or Off according to how you connected your TV. Press After Auto Program finishes, press to search for channels. to exit. To reset the TV to factory settings Turn the TV on. Press and release the POWER button on the TV front panel. The TV will turn itself off, then back on. [. . . ] If you enter a new code number, the code number you previously entered at that setting is erased. Use the component's own remote control. You must reprogram the remote control. 38 Other Information Video Problem No picture, no sound Possible Remedies Make sure the power cord is plugged in. If a red light is flashing on the front of your TV for more than a few minutes, disconnect and reconnect the power cord. If the problem continues, call your local service center. [. . . ]