User manual SONY KV-27EXR90

[. . . ] If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. Note to the CATV Installer This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building as close to the point of cable entry as practical. Reorient or relocate the receiving antennas. Increase the separation between the equipment and receiver. [. . . ] To do this, first program your remote control, then use the Channel Fix feature to set your TV to channel 3 or 4 (see page 29). Press repeatedly to switch between VCR input (VIDEO input) and VHF/UHF (local channels). 13 Operating Instructions TV and Cable Box Cable box 1 From cable/ antenna Rear of TV 1 3 4 S VIDEO P P 2 VIDEO L (MONO) R 1 2 Connect the coaxial cable from your cable service to the IN jack on your cable box. Connect a coaxial cable (not supplied) from the OUT jack on your cable box to the VHF/UHF jack on your TV. Using your TV with this connection This connection allows you to do the following: Program your Sony remote control to operate your cable box (see page 5). To activate your remote press to operate your cable box and then use the 0 9 buttons or CH+/- buttons to change the channels. To do this, first program your remote control, then use the Channel Fix feature to set your TV to channel 3 or 4 (see page 29). 14 Connecting Your TV TV, VCR, and Cable Box Rear of TV 1 3 4 Y 5 AUDIO OUT (VAR/FIX) 3 VCR 2 Cable Box 4 S VIDEO PB PR VIDEO L (MONO) L (MONO) R R Video (yellow) Audio L (white) Audio R (red) 1 From cable 1 2 3 4 Connect the coaxial cable from your cable service to the IN jack on your cable box. Connect a coaxial cable (not supplied) from the OUT jack on your cable box to the IN jack on your VCR. Connect a coaxial cable (not supplied) from the OUT jack on your VCR to the VHF/UHF jack on the TV. If your VCR is equipped with video outputs, you can get better picture quality by connecting audio/video cables (not supplied) from AUDIO/VIDEO OUT on your VCR to AUDIO/VIDEO IN on your TV. For better picture quality, use S VIDEO inserted of the yellow video cable. S VIDEO does not provide sound, so you still must connect the audio cables. Program your Sony remote control to operate your VCR or cable box (see page 5). Using the audio/video cables (not supplied), connect the AUDIO/VIDEO OUT on your camcorder to the AUDIO/VIDEO IN on your TV. Front A/V Panel A/V output Audio R (red) Audio L (white) Video (yellow) Connecting an Audio System 1 2 3 Using audio/video cables (not supplied), connect AUDIO OUT on your TV to one of the unused line inputs (e. g. For more instructions, see "Using the Audio Menu" on page 28. Open the Audio Out option on the Audio Menu and select Fixed to control the volume through the connected audio system. For more instructions, see "Using the Audio Menu" on page 28. For this connection you don't need to disconnect Dynamic Bass Response System. Rear of TV 1 3 4 Y 5 AUDIO OUT (VAR/FIX) S VIDEO PB PR VIDEO L (MONO) AUDIO-L (white) L (MONO) R R AUDIO-R (red) Line input 19 Using Basic Functions Setting Up the TV After you have finished connecting your TV, you can use Auto Program to set up your channels. During Auto Program, the TV will automatically search for available channels and program receivable channels. 1 When you start Auto Program wait until it is finished; otherwise it will skip over channels that are available. Perform Auto Program again to program receivable channels. Press to turn on the TV. The Initial Setup screen appears. Initial Setup Auto Program: [CH+] [CH­] Exit: First please connect cable/antenna 2 Press on the remote control or on the TV front panel to start Auto Program, or press to exit. The Initial Setup screen appears each time you turn on the TV until you perform Auto Program. 1 2 3 4 5 6 1 2 3 4 To perform Auto Program again Press . Press Press F or f to highlight On or Off according to how you connected your TV. Press After Auto Program finishes, press Turn the TV on. Press and release the POWER button on the TV front panel. The TV will turn itself off, then back on. [. . . ] Use the component's own remote control. You must reprogram the remote control (page 5). 42 Other Information Video Problem No picture, no sound Possible Remedies Make sure the power cord is plugged in. If a red light is flashing on the front of your TV for more than a few minutes, disconnect and reconnect the power cord. If the problem continues, call your local service center. Check the TV/VIDEO setting: when watching TV, set it to TV; when watching video equipment, set it to VIDEO 1, 2, 3, 4 or 5 (page 3). [. . . ]