User manual SONY KV-27TR21

[. . . ] Never use the plug without the fuse cover. If you should lose the fuse cover, please contact your nearest Sony service station. How to replace the fuse Open the fuse compartment with a blade screwdriver, and replace the fuse. · IMPORTANT If the plug supplied is not suitable for the socket outlets in your home, it should be cut off and an appropriate plug fitted in accordance with the following instructions: The wires in this mains lead are coloured in accordance with the following code: Blue Neutral Brown Live As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black. The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red. Do not connect either wire to the earth terminal in the plug which is marked by the letter E or by the safety earth symbol Y or coloured green or green and yellow. WARNING · To prevent the risk of electric shock, do not insert the plug cut off from the mains lead into a socket outlet. [. . . ] Compromise between 4:3 and 16:9 picture size. Smart 4:3 Zoom: Widescreen format for letterbox movies. Full picture information. 14:9 In "Smart", "Zoom" and "14:9" modes, parts of the top and bottom of the screen are cut off. Press or to adjust the position of the image on the screen (e. g. to read subtitles). Zoom Wide continued. . . 12 Menu System Level 1 Picture Adjustment Picture Mode Contrast Brightness Colour Sharpness Reset Noise Reduction Personal Level 2 Level 3 / Function AV3 OUTPUT The "AV3 Output" option in the "Features" menu allows you to select the source to be output from the Scart connector 3/ S 3 so that you can record from this Scart any signal coming from the TV or from an external equipment connected to the Scart connectors 1/ 1 or 2/ 2 or side connectors S 4 or 4 and 4. If your VCR supports Smartlink, this procedure is not necessary. To do this: after selecting the option, press Then press or to select the desired output signal: TV, AV1, AV2, AV4, YC4 or AUTO. . AUTO Select: Enter Menu: Features Sleep Timer Auto Format AV3 Output PIP Input PIP Position Off On AUTO AV1 Features Sleep Timer Auto Format AV3 Output PIP Input PIP Position Off On AUTO AV1 Select: Enter Menu: Select: Enter: If you select "AUTO", the output signal will always be the same one that is displayed on the screen. If you have connected a decoder to the Scart 3/ S 3 or to a VCR connected to this Scart, please remember to change back the "AV3 Output" to "AUTO" or "TV" for correct unscrambling. PIP INPUT The "PIP Input" option in the "Features" menu allows you to select the source you want to watch in the "PIP" screen. To do this: after selecting the option, press . Then press repeatedly or to select the desired source AV1, AV2, AV3, AV4 or TV. 3 After selecting the Channel option, press . Then press the number buttons to enter directly the channel number of the TV Broadcast or the channel of the VCR signal. If you do not know the channel number, press or to search for it. When you tune the desired channel, press OK twice to store. Repeat all the above steps to tune and store more channels. b) Label a channel using up to five characters. To do this: Highlighting the Programme option, press the PROG +/- button to select the programme number with the channel you wish to name. When the programme you want to name appears on the screen, select the Label option and press . Next press or to select a letter, number or "-" for a blank. Select the other four characters in the same way. After selecting all the characters, press OK twice to store. c) Fine tune the broadcast reception. Normally the automatic fine tuning (AFT) will give the best possible picture, however you can manually fine tune the TV to obtain a better picture reception in case the picture is distorted. [. . . ] · Using the menu system, select the "Picture Adjustment" menu and select "Reset" to return to factory settings. Press the number buttons on the remote control to select the desired channel. Poor or no picture (screen is dark), but good sound. No picture or no menu information from equipment connected to the Scart connector. Good picture, no sound. No colour on colour programmes. [. . . ]