User manual SONY LBT-D117CD

[. . . ] Refer servicing to qualified personnel only. Do not install the appliance in a confined space, such as a bookcase or built-in cabinet. Laser component in this product is capable of emitting radiation exceeding the limit for Class 1. This appliance is classified as a CLASS 1 LASER product. [. . . ] Press NON-STOP so the indicator on this button lights up. Press ·. Clear the entire program Tips · The program you created remains in the CD player's memory even after it has been played. Press · to play the same program again. · If "--. --" appears instead of the total playing time while programming, this means: ­ you have programmed a track numbered over 20, or ­ the total playing time has exceeded 100 minutes. To cancel Non-Stop Play Press NON-STOP so the indicator on this button goes off. 22 The Tape Deck Recording on a tape manually You can record from CDs, tapes, or the radio as you like. For example, you can record just the songs you want or begin recording from the middle of the tape. The recording level is adjusted automatically. 5 6 Press P on deck B. Recording starts. Start playing the source to be recorded. To Stop recording Pause recording Press p on deck B P on deck B 2 Tips · If you want to record on the reverse side, press ª so the indicator on the ª button (for the reverse side) lights up green. · When you want to reduce the hiss noise in lowlevel high-frequency signals, press DOLBY NR before step 5 so "DOLBY NR B" appears in the display. 4 DOLBY NR 1 2 3 ª p 5 13 Insert a blank tape into deck B. Press FUNCTION repeatedly until the source you want to record (e. g. , CD) appears in the display. Press r REC. Deck B stands by for recording, and the indicator on the · button (for the front side) lights up green. 4 Press DIRECTION repeatedly to select A to record on one side or ß (or RELAY) to record on both sides. 23 Recording CDs by specifying the track order -- Program Edit You can record tracks from all the CDs in the order you want. When programming, make sure the playing times for each side do not exceed the length of one side of the tape. 1 2 3 4 5 6 Place CDs and close the front cover. Press FUNCTION repeatedly until "CD" appears in the display. No sound will come from the speakers. To reinforce the bass (DBFB) (LBT-D390/G5500/XB33/XB33K/XB50 only) Press DBFB. * Each time you press this button, the DBFB level display changes as follows: n DBFB n DBFB n display off "DBFB "DBFB " reinforces the bass more than ". * DBFB = Dynamic Bass Feedback To reinforce the bass from the super woofer (SUPER WOOFER) (except for LBT-D390/G5500/XB33/ XB33K/XB50) Press SUPER WOOFER. Each time you press this button, the super woofer level display changes as follows: SUPER WOOFER FLAT n LOWn HIGH n 28 Selecting the audio emphasis The audio emphasis menu lets you select the sound characteristics according to the music you are listening to. The personal file function (see "Making a personal audio emphasis file (Personal File)") lets you store your own effects. SPECTRUM ANALYZER EFFECT Music menu options "SUR " appears if you select an audio emphasis with a surround effect. Press GEQ V/v GEQ B/b To select MENU 1 ROCK POP JAZZ DANCE SALSA MENU 2 MOVIE GAME NIGHT PARTY RELAX 1, 2 To change the equalizer display Each time you press SPECTRUM ANALYZER, the equalizer display changes to show one of the four displays below. LBT-D390/D790/ LBT-XB66/XB66K/XB660 G5500/XB33/XB33K/ XB44/XB44K/XB50/ XB60 DO ALL DISC S 1 Press GEQ V/v (or MUSIC MENU V/v on the remote) repeatedly to select MENU 1 or MENU 2. See the chart "Music menu options" below. The last audio emphasis chosen from that menu appears in the display. ALL DISC S DO 2 Press GEQ B/b (or MUSIC MENU B/b on the remote) repeatedly to select the audio emphasis you desire. The audio emphasis name appears in the display. DO ALL DISC S 63 250 1K 4K 16K(Hz) DO To cancel the audio emphasis Press EFFECT (or MUSIC MENU ON/OFF on the remote) repeatedly so the indicator on the EFFECT button goes off. ALL DISC S 29 Adjusting the audio emphasis You can adjust the audio emphasis using the graphic equalizer and surround effect. 4 Press GEQ V/v to adjust the level. LBT-D390/D790/G5500/XB33/XB33K/XB44/ XB44K/XB50/XB60 DOLBY NR OFF ALL DISC S Adjusting the graphic equalizer You can adjust the sound by raising or lowering the levels of specific frequency ranges. Before operation, first select the basic audio emphasis you want for your sound. LBT-XB66/XB66K/XB660 DOLBY NR OFF ALL DISC S 63 250 1K 4K 16K(Hz) 5 6 Repeat steps 3 and 4 to adjust the other frequency bands. Press ENTER when finished. 6 2 3, 4 Note If you choose another audio emphasis (other than "EFFECT OFF"), the adjusted sound effect is lost. To retain the adjusted sound effect for future use, store it in a personal file (see "Making a personal audio emphasis file"). Activating the surround effect 1 2 3 You can enjoy the surround effect. Select the basic audio emphasis you want for your sound (see "Selecting the audio emphasis"). Press GEQ CONTROL. The frequency range appears and the level value flashes in the display. SURROUND ­ + 9 Press GEQ B/b repeatedly to select a frequency band. LBT-D390/D790/G5500/XB33/XB33K/XB44/ XB44K/XB50/XB60 DOLBY NR OFF ª ª ª ª / Press SURROUND so "SUR appears in the display. Note " ALL DISC S LBT-XB66/XB66K/XB660 DOLBY NR OFF ALL DISC S 63 250 1K 4K 16K(Hz) If you choose other sound effects, the surround effect will be canceled. To retain the effect, store it in a personal file (see "Making a personal audio emphasis file"). 30 Making a personal audio emphasis file -- Personal File You can create personal files of audio patterns (surround effect and graphic equalizer) and store them in the unit's memory. Later call up an audio pattern to play a favorite tape, CD, or radio program. Before operation, first select the basic audio emphasis you want for your sound. 4 Press ENTER. The adjusted sound effects are stored under the selected file number. [. . . ] ·The capstans or pinch rollers are dirty. Noise increases or the high frequencies are missing. ·The record/playback heads are magnetized. Demagnetize them (see page 40). 42 Specifications For the U. S. [. . . ]