User manual SONY MAVEF555 OPERATING MANUAL

[. . . ] EDITING PANEL (for MAV-555 MULTI ACCESS VIDEO DISK RECORDER) MAVE-F555 (Ver. 2. 30) OPERATION MANUAL [Japanese/English] 1st Edition (Revised 2) Serial No. 10001 and Higher , 1 OFF IN1(EDITOR R) IN2(EDITOR P) POWER OUT1(MAV P1) OUT2(VTR) TO MAV(PARALLEL I/O) AV SEL OUT D555 I/F TO MAV 1 2 DC IN(12V) 2 3 , 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 1-1 MAVE-F555 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Holding down the SHIFT key on the MAVE-F555, press the MARK IN key. This specifies the IN point for the source for the replacement cut. The same as the IN point, use the MAVE-D555 or BVE-series editor jog dial to search for the OUT point. Holding down the SHIFT key on the MAVE-F555, press the MARK OUT key. This specifies the OUT point for the source for the replacement cut. Now continue from step 8 of the procedure under "Replacing a section on the recorder with a cut specified on the player" (page 3-25). Chapter 3 Operations for Linear/Nonlinear Editing 3-27 (E) 3-2 Operations for Nonlinear Editing (Operations in Cut Units) 3-2-5 Cut Overwriting (Editing Using OVERWRITE mode) In OVERWRITE mode, you set a total of three edit points, both IN points and either one of the OUT points on the recorder and player, then carry out overwrite editing. Operation in OVERWRITE mode The editing operation in OVERWRITE mode is as follows. · Regardless of the order in which you set the edit points, once you have set both player and recorder IN points and either one of the OUT points, you can execute the edit. The fourth edit point is calculated automatically. Automatic calculation of fourth edit point Player IN Recorder IN OUT OUT Result of executing edit · If all four of the IN and OUT points on the player and recorder are set, then the OUT point on the recorder takes precedence over the OUT point on the player. Ignored Player IN Recorder IN OUT OUT Result of executing edit 3-28 (E) Chapter 3 Operations for Linear/Nonlinear Editing Handling of exceptional cases If the recorder OUT point calculated automatically from the player IN and OUT points and the recorder IN point is outside the outside the range of the file on the recorder, the length of the file on the recorder as the editing result is increased as shown in the figure below. Player IN Recorder IN OUT Automatic calculation of fourth edit point t allowed even if out of range Result of executing edit Notes · As in conventional linear editing, the OUT point is not included in the editing interval. Therefore, it is not possible to specify up to the last frame of the recorder file to be overwritten. To overwrite up to and including the last frame of the recorder file, leave the recorder OUT point unset, as above, and carry out the overwriting with only the player OUT point set. You can also use this function with a BLACK/MUTING loaded on the player to delete up to and including the last frame of the recorder file. · To overwrite everything up through the last frame, use the ten-keys of the MAVE-D555 to specify the end point of the file plus one frame as the OUT point. Chapter 3 Operations for Linear/Nonlinear Editing 3-29 (E) 3-2 Operations for Nonlinear Editing (Operations in Cut Units) Overwriting a cut The operation for overwriting a cut depends slightly on whether the section used for overwriting is specified on the player, or whether a section on the recorder is specified as the source for overwriting (in other words, an operation within a single file). Overwriting a specified section on the recorder with a cut from the player PORT/FILE ASSIGN R P1 P2 BG 4 1 2 + STORE - REDO UNDO V A1 A2 A3 A4 6 TRIM 3, 5 MARK IN MARK OUT MARK SPLIT SHIFT EXECUTE/ REC REPLAY PREVIEW 7 1 Press the [ ] key, and select OVERWRITE mode. In the following steps 2 to 5, all of the player and recorder port IN and OUT points are set, but either of the player and recorder OUT points may be left unset. 2 3 3-30 (E) Chapter 3 Select the player port. To select another file, follow the procedure in the section "Selecting a file" (page 3-1). Press the MARK IN key and MARK OUT key on the MAVE-F555 to set the IN point and OUT point respectively. Operations for Linear/Nonlinear Editing · Using the jog dial of the MAVE-D555 or BVE-series editor, for example, search for the IN point and OUT point. · The time data of the IN point and OUT point appear on the monitor screen connected. While player port is selected IN point/OUT point P IN OU T DUR 00 : 10 : 01 : 00 00 : 10 : 03 : 00 00 : 00 : 02 : 00 Duration V1234 4 5 Select the recorder port. Press the MARK IN key and MARK OUT key on the MAVE-F555 to set the IN point and OUT point respectively. · Using the jog dial of the MAVE-D555 or BVE-series editor, for example, search for the IN point and OUT point. · The time data of the IN point and OUT point appear on the monitor screen connected. While recorder port is selected IN point/OUT point R IN OU T DUR 00 : 10 : 01 : 00 00 : 10 : 03 : 00 00 : 00 : 02 : 00 Duration V1234 ED I T 6 Using the channel specification keys (V, A1, A2, A3, and A4), select the channel(s) which you will overwrite with the cut. · Press the key(s) corresponding to the channel(s) you want to overwrite, turning on the indicator(s) above the key(s). · If you select only specific channels to overwrite, see next page "Notes". [. . . ] IN point Time Data Displays the Time Data in the format HH:MM:SS:FF for the specified IN point. Appendixes A-7 (E) List of Superimposed Indication OUT point Time Data Displays the Time Data in the format HH:MM:SS:FF for the specified OUT point. Duration Displays the Time Data in the format HH:MM:SS:FF automatically calculated from the IN point to the specified OUT point specified during editing. During DMC editing, a "D" is displayed to the right of the time data. Edit mode Displays the channel currently targeted for editing and the edit mode. [. . . ]