User manual SONY MDS-JE440

[. . . ] And don't place lighted candles on the apparatus. To prevent fire or shock hazard, do not place objects filled with liquids, such as vases, on the apparatus. This appliance is classified as a CLASS 1 LASER product. This label is located on the rear exterior. [. . . ] To see the rest of the program, turn AMS (or press > repeatedly). Changing the contents of the program Playing MDs While the deck is stopped and "PGM" lights up, do steps 2 to 4, followed by one of the procedures below: To Erase a track Do the following: Press m/M repeatedly until the number of the unwanted track flashes, then press CLEAR. Press down CLEAR until all the track numbers disappear. Press m repeatedly until "0" flashes before the first track number, then do steps 5 to 7. Press m/M repeatedly until the track number which will precede the new track flashes. Press AMS to display flashing "0, " then do steps 5 to 7. Press M repeatedly until "0" flashes after the last track number, then do steps 5 to 7. Press m/M repeatedly until the number of the track to be changed flashes, then do steps 5 to 7. Press m/M repeatedly until the wrong track number flashes, then do step 5 above again or press CLEAR to erase the track number. If "0" flashes, press m so that the last track number flashes, then enter a correct number. To enter a track number over 10 Erase all tracks Add a track at the beginning of the program Add a track in the middle of the program Use >10. For details, see page 21. 6 Repeat step 5 to enter other tracks. The entered track is added to the location where the "0" flashes. Each time you enter a track, the total program time appears in the display. 7 Press YES. "Complete!" appears and the program is completed. 8 Press H. Program Play starts. To stop Program Play Add a track to the end of the program Replace a track Press x. Notes · If you eject the MD, the program will be lost. · The display shows "- - - . This is due to a technical limitation of the MD system and is not a mechanical error. You can shift the starting point by 1-frame1) intervals (1 frame = 1/86 second). The time indication (minute, second, and frame) of the current point is displayed and the deck plays several seconds of the track to that point repeatedly. 1) During Stereo recording: In Monaural or LP2 Stereo mode: 2-frame intervals In LP4 Stereo mode: 4-frame intervals Editing Recorded MDs Dividing recorded tracks -- Divide Function You can use this function to mark track numbers after recording. The total number of tracks increases by one and all the tracks following the divided ones are renumbered. Example: Dividing track 2 into two tracks. Track number 1 Original tracks To find a point quickly Specify a unit (minute, second, or frame) by which the MD is advanced when you turn AMS (or press . /> repeatedly). To do this, press m/M in step 4 repeatedly to select minute, second, or frame. The selected unit flashes in the display. 5 Repeat step 4 until you have located the 2 3 dividing point. A 2 B 3 C D 6 Press AMS or YES. "Complete!" appears and the deck starts to play the newly created track. Note that new track has no name. Tip After DIVIDE 1 Divide track 2 into track B and C 4 A B C D Dividing a track after selecting the track You can divide tracks while recording. For details, see "Marking track numbers while recording" on page 15. 1 While the deck is stopped, playing, or paused, press MENU/NO. "Edit Menu" appears in the display. 2 Turn AMS (or press . /> repeatedly) until "Divide?" appears, then press AMS or YES. 3 Turn AMS (or press . /> repeatedly) until the number of the track you want to divide appears, then press AMS or YES at the dividing point. "-Rehearsal-" appears and the deck repeatedly plays several seconds of the track from the point AMS or YES was pressed. 27 Combining recorded tracks -- Combine Function You can use this function to combine 2 tracks into a single track. The total number of tracks decreases by one and all tracks following the combined ones are renumbered. You can also use this function to erase unnecessary track numbers. Example: Combining track 3 to track 1. Track number Original tracks 4 Turn AMS (or press . /> repeatedly) until the number of the second track of the two to be combined appears, then press AMS or YES. "Complete!" appears and the deck starts to play the combined track. Notes 1 2 3 4 A 1 B 2 C 3 D After COMBINE A C B D · (MDS-JE770 only) When you combine two tracks that are registered into different groups, the second track is re-registered into the group containing the first track. [. . . ] Repeat the recording procedure. The deck does not perform Synchro-recording with a CD player or video CD player. , Set the deck in a stable surface, and repeat the recording procedure. · The inserted MD is dirty (with smudges, fingerprints, etc. ), scratched, or substandard in quality. , Replace the disc and repeat the recording procedure. C13/Read Error , Take out the MD and insert it again. C14/Toc Error , Insert another disc. , If possible, erase all the tracks on the MD (page 26). C41/Cannot Copy The remote supplied with the MD deck is not set correctly. [. . . ]