User manual SONY MDS-E10

[. . . ] 2-347-256-11(1) Mini-disc Recorder TABLE OF CONTENTS Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Location and Function of Parts 6 Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Recording on MDs . . . . . . . . . . . . . . . . . . . . 18 Playing MDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] "Setup Menu" appears in the display. 2 Turn AMS (or press . /> repeatedly) to select "Direct Mark", then press AMS or YES. 3 Turn AMS to display the track number to be located , then turn AMS. 2T r 0m00s 00f 4 Similarly with step 3, set minutes, seconds, and frames in order to locate a point. "Complete!" appears and "Mark" lights up at the display window, then normal display is returned. You can slide a position for each frame* (f) (1 frame = 1/86 seconds). * Monaural or LP2 stereo tracks move two frames at a time, LP4 stereo tracks move four frames at a time. To set quickly, press m/M repeatedly in step 4. Change units advanced when AMS is turned (or m/M is pressed) to frames, seconds, or minutes. 36 Fine adjusting the marked point (Rehearsal) You can fine adjust the determined point while monitoring the sound of play. Pausing After Each Track (Auto Pause) You can set the MD recorder so that it pauses automatically at the beginning of the next track after play back of each track. This is convenient to record one track only or several uncontinuous tracks. 1 While the recorder is stopped, press MENU/NO twice. "Setup Menu" appears in the display. Turn AMS (or press . /> repeatedly) to select "Mark Rehear", then press AMS or YES. "-Rehearsal-" flashes and play is repeated for several seconds from the already determined point. 2 M. ACCESS CONTINUE SHUFFLE PROGRAM 1 2 7 12 17 22 3 8 13 18 23 4 9 14 19 24 5 10 15 20 25 -Rehearsal3m43s04f 3 Turn AMS (or press . /> repeatedly) to move the location of a track. You can slide a position for each frame* (f) (1 frame = 1/86 seconds). * Moraural or LP2 stereo tracks move two frames at a time, LP4 stereo tracks move four frames at a time. To set quickly, press m/M repeatedly in step 4. Change units advanced when AMS is turned (or . / > is pressed) to frames, seconds, or minutes. After the point is determined, press AMS or YES. "Complete" appears and normal display is returned. AUTO CUE A. CUE A. PAUSE 6 11 16 21 >25 NAME CHAR NUM RM-DR1J Playing MDs Press AUTO CUE repeatedly until "A. PAUSE" appears at the display window. (Or press A. CUE/A. PAUSE. ) 4 Notes · If the point (MARK) is not determined, "Mark Rehear" of "Setup Menu" does not appear. · Adjustment of the point in Rehearsal cannot be moved over the track. To stop Auto Pause Press AUTO CUE repeatedly until "A. PAUSE" at the display window disappears. (Or press A. CUE/A. PAUSE. ) To locate the marked point When LOCATE is pressed, play pauses in the determined marked point. You can start playing again from the same location. [. . . ] Material: GaAlAs 400 rpm to 900 rpm (CLV) ACIRC (Advanced Cross Interleave Reed Solomon Code) 44. 1 kHz ATRAC (Adaptive Transform Acoustic Coding)/ATRAC 3 EFM (Eight-to-Fourteen Modulation) Two stereo channels 5 to 20, 000 Hz ±0. 3dB Over 98dB during playback Below measurable limit General Power requirements Where purchased USA and Canada Other countries Power consumption Dimensions (approx. ) Power requirements 120V AC, 60 Hz 120V or 230V AC Selectable, 50/60 Hz 16W 482 x 44 x 290 mm (19 x 13/ x11 3/8 in) 4 (w/h/d, including projecting parts) 3. 2 kg (7 lbs. 1 oz. ) 0 °C to +40 °C _5 °C to +60 °C Laser diode Revolutions Error correction Sampling frequency Coding Modulation system Number of channels Frequency response Signal-to-noise ratio Wow and flutter Input Terminals Terminal name Analog IN (UNBAL) Digital IN (OPTICAL) Terminal type Pin jack Square optical MASS (approx. ) Operating temperature Storage temperature: Accessories See page 15 US and foreign patents licensed from Dolby Laboratories. Design and specifications are subject to change without notice. Input Reference Maximum impedance input level input level 47k _4dBu +12dBu 660 nm -- (optical wave length) 75 0. 5 Vp-p ±20% -- Digital IN Pin jack (COAXIAL) Additional Information Output Terminals Terminal type Standard stereo jack Analog OUT Pin jack (UNBAL) Digital OUT Square (OPTICAL) optical Digital OUT Pin jack (COAXIAL) 0dBu=0. 775Vrms Terminal name PHONES -- Reference output level 0 to 10mW (level variable) Maximum + 8dBu _ 18dBm (optical power) 0. 5 Vp-p (at 75) Load impedance 32 Greater than 10k 660nm (optical wave length) 75 64 Exterior dimensions 430 482 44 265 290 Units: mm Rack mounting This recorder can be rack mounted on a standard EIA 19inch rack. After removing the four feet, the unit can be mounted in a rack. [. . . ]