User manual SONY MEU-VX1

[. . . ] 4-098-710-15 (1) Multiformat Engine Unit Operating Instructions MEU-WX1 © 2003 Sony Corporation English Owner's Record The model and serial numbers are located at the bottom. Record these numbers in the spaces provided below. Refer to these numbers whenever you call upon your Sony dealer regarding this product. ____________________ WARNING To prevent fire or shock hazard, do not expose the unit to rain or moisture. [. . . ] Press the A-1, A-2, B-1 or B-2 button to select the signal. g AC IN socket Connect the supplied AC power cord. h DC 12V IN connector (XLR) Plug the DC 12V power supply to this connector to provide power to the Multiformat Engine and monitor. The operable monitor is as follows; LMD-170W i Loop-through output connectors (BNC) The signals input to the input connectors (a, b and c) are output here. Connect to the analog input (composite/Y/C, analog component or analog RGB) of equipment, according to the input signal. When inputting a video signal with the jitters, etc. We recommend using the TBC (time base corrector). OUT connector Loop-through output of the IN connector. Connect to the external sync input of video equipment to be synchronized with this unit. * Composite and Y/C signals can be input at the same time. Convert a plug to the BNC type for connecting Y/C signals. Component and RGB signals cannot be input at the same time because three connectors are used. If necessary, set the output signals for the speakers on the front panel and AUDIO MONITOR OUT connector in the USER CONFIG menu. For details, see page 25. Location and Function of Parts and Controls 13 j AUDIO MONITOR OUT connector (stereo mini jack) The audio signal which is selected by the input select button on the front panel is output. When an analog video signal is input, the signal which is set in the USER CONFIG menu is output (see page 11 and 25). When an input adaptor is attached, the channel which is set in the OPTION CONFIG menu is output (see page 28). The audio signal from this connector is monitored on the front speakers (see page 11). k PARALLEL REMOTE terminal (modular connector) Forms a parallel switch and controls the Multiformat Engine externally. For details on the pin assignment and factory setting function assigned to each pin, see page 30. l COMPUTER SIGNAL IN connector (D-sub 15 pin, female) Connect to the monitor output on a computer. Only the computer signal can be input to this terminal. Press the COMPUTER button to select the signal. The Plug & Play function corresponds to DDC2B. m COMPUTER AUDIO connector (stereo mini jack) Connect to the audio output connector of the computer. [. . . ] The following lists the functions you can assign to the pins. R E M O T E PA R A L L E L x1 P I N xxxxx · 2PIN xxxxx · 3PIN xxxxxxx · 4PIN xxxxxxx · 6PIN xxxxxxxx · 7PIN xxxxxxxxx · 8PIN xxxx OPTION CONFIG menu Sets an optional input adaptor. OPTION CONFIG OPTION A xB K M ­ 2 4 3 H S xxxxxx OPTION B · N O T I N S TA L L E D OPTION A BKM­243HS xAU D I O C H xxxxxxx · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · ­ ­ ("­ ­": No function is assigned. ) Composite Y/C RGB Component Computer Option A-1 Option A-2 Option B-1 Option B-2 Tally R Tally G Zero scan Full Zoom 16:9 4:3 Ext sync Blue only Mono H/V delay 16:9 marker 15:9 marker 14:9 marker 13:9 marker 4:3 marker 1. 85:1 marker 2. 35:1 marker 1. 85:1 & 4:3 marker Center marker Safe area 80 % Safe area 85 % Safe area 88 % Safe area 90 % Safe area 93 % Note Submenu AUDIO Setting Selects an audio channel. When BKM-220D/243HS is installed CH1, CH2, CH1+CH2, CH3, CH4, CH3+CH4, CH5, CH6, CH5+CH6, CH7, CH8, CH7+CH8, CH9, CH10, CH9+CH10, CH11, CH12, CH11+CH12, CH13, CH14, CH13+CH14, CH15, CH16, CH15+CH16, OFF When BKM-255DV is installed CH1, CH2, CH1+CH2, CH3, CH4, CH3+CH4, CH1/3, CH2/4, CH1/ 3+CH2/4, OFF KEY INHIBIT menu KEY INHIBIT xK E Y I N H I B I T xxx You can lock the setting so that they cannot be changed by an unauthorized user. If you set ON, all items are displayed in blue, indicating the items are locked. If you use the PARALLEL REMOTE function, you need to connect cables. For more details, see page 30. 28 Adjustment Using the Menus Troubleshooting This section may help you isolate the cause of a problem and as a result, eliminate the need to contact technical support. [. . . ]