User manual SONY MHC-GRX9900

[. . . ] Refer servicing to qualified personnel only. Do not install the appliance in a confined space, such as a bookcase or built-in cabinet. Laser component in this product is capable of emitting radiation exceeding the limit for Class 1. This appliance is classified as a CLASS 1 LASER product. [. . . ] Skip step 3 to select tracks from the same disc. Press CD (P. All the tracks play in the order you selected. 7 continued VOL +/­ 23 Programming the CD tracks (continued) To cancel Program Play Press PLAY MODE repeatedly until "PROGRAM" or "SHUFFLE" disappears from the display. To Check the program Press CHECK on the remote repeatedly. After the last track, "CHECK END" appears. CHECK on the remote repeatedly until the number of the track to be erased lights up, then press CLEAR. 1 Select the disc tray with a DISC 1~3 button. 2 Select the track by turning the jog dial. p once in stop mode or twice while playing. Playing CDs without interruption ­­ Non-Stop Play You can play CDs without pausing between tracks. (Power) 12 3 Clear a track from the end Clear a specific track Add a track to the program Clear the entire program 1 2 Tips · The program you made remains in the CD player even after it has been played back. Press CD (P to play the same program again. · If "--. --" appears instead of the total playing time during programming, this means: ­ you have programmed a track number which exceeds 20. ­ the total playing time has exceeded 100 minutes. Press FUNCTION repeatedly until "CD" appears in the display, then place a CD. Press NON-STOP to light the indicator. "NON-STOP PLAY" appears in the display. 3 Press CD (P. To cancel Non-Stop Play Press NON-STOP so that the indicator goes out and "NON-STOP OFF" appears in the display. 24 The Tape Deck Recording on a tape manually You can record from CD, tape, or radio as you like. After the last track, "CHECK END" appears. To cancel Program Edit Press PLAY MODE repeatedly until "PROGRAM" or "SHUFFLE" disappears from the display. Tip When you want to reduce the hiss noise in low-level high-frequency signals, press DOLBY NR so that "DOLBY NR" appears after pressing CD SYNC. 27 DJ Effects Looping part of a CD -- Loop With the loop function, you can repeat part of a CD during playback. This lets you create original recordings. (Power) LOOP Flashing part of a CD -- Flash With the flash function, you can "flash" the CD sound during playback. This lets you create original recordings. (Power) FLASH Jog dial Jog dial / Press and hold LOOP during playback at the point you want to start the Loop function, and release to resume normal play. To adjust the loop length Turn the jog dial while holding LOOP (or press MUSIC MENU > or . while holding LOOP on the remote) to select different loop lengths (LOOP 1~20). / Press and hold FLASH during playback at the point you want to start the Flash function, and release to resume normal play. To adjust the flash length Turn the jog dial while holding FLASH (or press MUSIC MENU > or . while holding FLASH on the remote) to select different flash lengths (FLASH 1~20). To use LOOP and FLASH together Press and hold both LOOP and FLASH at the same time. Notes · The loop and flash length cannot be adjusted during this operation. Adjust the loop and flash lengths independently beforehand if necessary. · To record the flash effect, use the analog (MD/ VIDEO OUT) connections or this unit's tape deck. 28 Sound Adjustment Adjusting the sound You can reinforce the bass, create a more powerful sound, and listen with headphones. (Power) DBFB GROOVE PHONES Notes · With some songs, the music will sound distorted when you use the DBFB system with the graphic equalizer if the bass is too strong. [. . . ] There is excessive wow or flutter, or the sound drops out. ·The capstans or pinch rollers are dirty. Clean them (see "Cleaning the tape heads" on page 44). Noise increases or the high frequencies are erased. [. . . ]