User manual SONY MHC-GSX75

[. . . ] Refer servicing to qualified personnel only. Do not install the appliance in a confined space, such as a bookcase or built-in cabinet. INFORMATION This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. [. . . ] Press one of the DISC 1~5 buttons to select a CD. To programme all the tracks on a CD at once, proceed to step 5. To cancel Programme Play Press PLAY MODE repeatedly until "PROGRAM" or "SHUFFLE" disappears from the display. To Check the programme Clear a track from the end Press CHECK on the remote repeatedly. After the last track, "CHECK END" appears. CLEAR on the remote in stop mode. 4 Turn the jog dial until the desired track appears in the display. Disc number 3 Clear a specific CHECK on the remote track repeatedly until the number of the track to be erased lights up, then press CLEAR. Add a track to 1 Select the disc tray with a the programme DISC 1~5 button. 2 Select the track by turning the jog dial. Clear the entire once in stop mode or twice programme while playing. PROGRAM Track number 5 Press ENTER. The track is programmed. The last programmed track and the total programmed track number appear, followed by the total playing time. Total playing time Tips · The programme you made remains in the CD player even after it has been played back. Press · to play the same programme again. · If "--. --" appears instead of the total playing time during programming, this means: ­ you have programmed a track number which exceeds 20 ­ the total playing time has exceeded 100 minutes. PROGRAM The last programmed track 6 To programme additional tracks, repeat steps 3 to 5. Skip step 3 to select tracks from the same disc. Press ·. All the tracks play in the order you selected. 7 21 The Tape Deck Recording on a tape manually You can record from CD, tape, or radio as you like. Tip When you want to reduce the hiss noise in low-level high-frequency signals, press DOLBY NR so that "DOLBY NR" appears after pressing CD SYNC. 24 Sound Adjustment Adjusting the sound You can reinforce the bass, create a more powerful sound, and listen with headphones. 1/u (power) For a powerful sound (GROOVE) Press GROOVE. The volume switches to power mode, DBFB is automatically set to full strength, the equalizer curve changes, and GROOVE button lights up. Press GROOVE again to return to the previous volume. Notes · With some songs, the music will sound distorted when you use the DBFB system with the sound effect if the bass is too strong. Set the DBFB to "DBFB" or "OFF", or cancel the sound effect (page 26). · Cancelling GROOVE sets DBFB to "DBFB" and flattens the equalizer curve. To cancel the DBFB level, press DBFB until the indication disappears. DBFB ­ 0 + ) To listen through the headphones + ­ + Connect the headphones to PHONES jack. Note If you have connected a super woofer, please note that sound comes from the super woofer even when the headphones are connected. Turn off the power of the super woofer when using headphones. g PHONES GROOVE To reinforce bass (DBFB) Press DBFB*. Every time you press the button, the display changes as follows: n DBFB NORMAL ( DBFB ) µ DBFB HIGH ( DBFB ) µ DBFB OFF (off) * DBFB = Dynamic Bass Feedback 25 Selecting the audio emphasis The audio emphasis menu lets you select the sound characteristic according to the sound you are listening to. Besides, you can also enjoy audio emphasis using the synchronized equalizer function. [. . . ] Demagnetize them (see "Demagnetizing the tape heads" on page 39). · The record/playback heads are magnetized. Demagnetize them (see "Demagnetizing the tape heads" on page 39). There is excessive wow or flutter, or the sound drops out. [. . . ]