User manual SONY MHC-771REV

[. . . ] EN 2 Sony Corporation Printed in Malaysia 3-810-989-51(1) Mini Hi-Fi Component System Operating Instructions EN EN f MHC-771 ©1996 by Sony Corporation 3 WARNING To prevent fire or shock hazard, do not expose the unit to rain or moisture. To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only. Do not install the appliance in a confined space, such as a bookcase or built-in cabinet. Note on CATV system installer: This reminder is provided to call CATV system installer's attention to Article 820­40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical. CAUTION The use of optical instruments with this product will increase eye hazard. NOTICE FOR THE CUSTOMERS IN THE U. [. . . ] and 4 to 6 from another CD to program the remaining tracks you want to record on side A in the order you want them to be recorded. Recording From the Radio You can record from the tuner onto a tape. Use TYPE I (normal) or TYPE II (CrO2) tape. 8 Press on the remote to pause recording at the end of side A. The total playing time "0. 00" is displayed. POWERnON 9 Repeat steps 5 and 6 from the same CD and 4 to 6 from another CD to program the remaining tracks you want to record on side B in the order you want them to be recorded. 5 4 2 6 1 DOLBY NR POWERnON DISC SKIP EX-CHANGE EN 6 3 11 2 4 1 5 13 12 10 10 Press § EJECT and insert a blank tape into deck B with the side you want to record on facing forward. Recording will start from the front side of the tape, unless you have changed the playing direction before recording. Make sure the tabs on the cassette have not been removed. 11 Select dual or single-sided recording. To record Press DIRECTION to select 1 Press § EJECT and insert a blank tape into deck B with the side you want to record on facing forward. Recording will start from the front side of the tape, unless you have changed the playing direction before recording. Make sure the tabs on the cassette have not been removed. DOLBY NR One side of the tape A ß or RELAY 8, 13 5 CHECK Both sides* * 2 1 Recording always stops at the end of the reverse side. Be sure to start from the front side. 2 Press TUNER/BAND several times until the desired radio band appears. 12 Press CD SYNCHRO. Deck B stands by for recording. 3 Tune in the radio station you want to record. (See "Listening to the Radio", or "Playing Preset Radio Stations" for details. ) 13 Press PAUSE to release recording pause. After about 10 seconds, the CD starts playing. To stop recording Press on deck or the CD player. To check the order Press CHECK on the remote repeatedly. Each time you press CHECK, the number of the programmed tracks appear in the display. 4 Select dual or single-sided recording. To record Press DIRECTION to select 1 Press FUNCTION repeatedly until "CD" appears in the display. One side of the tape Both sides* * A ß or RELAY 2 Press § OPEN/CLOSE and place a CD. Then, press § OPEN/CLOSE again to close the disc tray. If the button for the disc tray containing the CD you want to record is not lit green, press DISC SKIP EX-CHANGE repeatedly so that it lights green. Recording always stops at the end of the reverse side. Be sure to start from the front side. continue to next page Chapter 4: the Tape Player 17 continued 1 Press § EJECT and insert a recorded tape in deck A with the side you want to play facing forward. Also, insert a blank tape in deck B with the side you want to record on facing forward. Recording and playback will start from the front side of the tape, unless you have changed the playing direction before recording. Make sure the tabs on the cassette have not been removed. POWERnON 5 Press ® REC. Deck B stands by for recording. 6 Press PAUSE to release recording pause. To reduce noise during AM recording If a whistling noise is heard while recording, reorient the AM loop antenna for optimum reception. To activate DOLBY NR 4 3 6 1 DOLBY NR 2 5 1 2 Choose how you want the tape to record and press DIRECTION. Indication Operation A ß When you want to reduce the hiss noise in low-level high-frequency signals, press DOLBY NR so that "DOLBY NR B" appears in the display after step 4. Dubbing stops at the end of one side. When the tape in one deck comes to the end of the front side, it reverses immediately regardless of the tape position in the other deck. When the tape in one deck reaches its end of the front side, it stops until the other tape come to its end, and then both tapes reverse together. 1 Press § EJECT and insert a recorded tape in deck A with the side you want to play facing forward. Also, insert a blank tape in deck B with the side you want to record on facing forward. [. . . ] model AUDIO POWER SPECIFICATIONS POWER OUTPUT AND TOTAL HARMONIC DISTORTION: With 6 ohm loads, both channels driven, from 40 ­ 20, 000 Hz; rated 50 watts per channel minimum RMS power, with no more than 0. 9 % total harmonic distortion from 250 milliwatts to rated output. CD player section System Compact disc and digital audio system Laser Semiconductor laser (=780 nm) Emission duration: continuous Laser output Max. 44. 6 µW* * This output is the value measured at a distance of 200 mm from the objective lens surface on the Optical Pick-up Block with 7 mm aperture. Frequency response 2 Hz ­ 20 kHz (±0. 5 dB) Wavelength 780 ­ 790 nm Signal-to-noise ratio More than 90 dB Dynamic range More than 90 dB Tuner section FM stereo, FM/AM superheterodyne tuner FM tuner section Amplifier section Continuous RMS power output U. S. model: 50 W + 50 W (6 ohms at 40 ­ 20, 000Hz, 0. 8 % THD) Canadian model: 50 W + 50 W (8 ohms at 1 kHz, 5% THD) Inputs 100 CD/VIDEO IN (phono jacks): voltage 450 mV, impedance 47 kilohms MIX MIC (phone jacks): sensitivity 1 mV, impedance 10 kilohms Outputs 100 CD/VIDEO OUT (phono jacks): voltage 250 mV impedance 1 kilohms PHONES (stereo phone jack): accepts headphones of 8 ohms or more. [. . . ]