User manual SONY MKS8080E

[. . . ] AUX BUS REMOTE PANEL MKS-8080/8082 OPERATION MANUAL 1st Edition [English] WARNING To prevent fire or shock hazard, do not expose the unit to rain or moisture. To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only. Using this unit at a voltage other than 120V may require the use of a different line cord or attachment plug, or both. To reduce the risk of fire or electric shock, refer servicing to qualified service personnel. [. . . ] The setting display of menu item D appears. Setting display (example) SONY ROUTING SYSTEM SETUP MENU MKS-8082 V1. 00 STATION NUMBER 6 SET AUX DESTINATION CONTROL DESTINATION = OUT001 01 KEY=OUT001 02 KEY=OUT002 03 KEY=OUT003 04 KEY=OUT004 05 KEY=OUT005 06 KEY=OUT006 07 KEY=OUT007 08 KEY=OUT008 09 KEY=OUT009 10 KEY=OUT010 11 KEY=OUT011 12 KEY=OUT012 13 KEY=OUT013 14 KEY=OUT014 15 KEY=OUT015 16 KEY=OUT016 ===================================================================== SET SOURCE TABLE +-------------+-----------+ DISPLAY BUS = Main | VIDEO | KEY | PANEL = MVS KEYS +------------+------------+ 001 = 001 | IN001 | IN128 | 002 = 002 | IN002 | IN127 | 003 = 003 | IN003 | IN126 | 004 = 004 | IN004 | IN125 | 005 = 005 | IN005 | IN124 | 006 = 006 | IN006 | IN123 | 007 = 007 | IN007 | IN122 | 008 = 008 | IN008 | IN121 | 009 = 009 | IN009 | IN120 | 010 = 010 | IN010 | IN119 | 011 = 011 | IN011 | IN118 | 012 = 012 | IN012 | IN117 | 013 = 013 | IN013 | IN116 | F1 : MOVE Ctrl-E : MENU Ctrl-D : RETURN Ctrl-N : DESCRIP. The entered name is registered. To set SET SOURCE TABLE 1 Press [F1]. The cursor moves to the SET SOURCE TABLE block, and the DISPLAY BUS number set for the destination where the cursor was placed before pressing [F1] appears at DISPLAY BUS. Settings for VIDEO and KEY depend on the DISPLAY BUS number. PANEL 001 through 032 and 121 through 124 are the source names normally displayed. PANEL 033 through 064 and 125 through 128 are enabled when the SHIFT function is set for a select button in menu item N. PANEL 065 through 120 are not used in normal operation. In the SET SOURCE TABLE block, you may assign any MVS KEYS to a select button on the panel only one time. 2 Setting procedure To set SET AUX DESTINATION Place the cursor to MVS KEYS to be changed using the cursor keys. If you press 4 at the bottom of the display, the next page appears, and if you press $ at the top of the display, the previous page will appear. 1 2 Select a button number using the cursor keys. If you press [Enter] again before entering a name, Name Input mode is canceled. 3 Press [Enter]. The unit enters MVS KEYS Number Input mode. If you press [Enter] again, this mode will be canceled. 4 3 a) When the setting of primary station menu item "J: NAME STYLE" is "Type + Num": To set the source name and destination name, select the type name from the list in the lower portion of the display using [0] to [F], then enter a number. b) When the setting of primary station menu item "J: NAME STYLE" is "DESCRIP. NAME": Two input modes are available. Each time you press [Ctrl]-[N], Description Input mode and Type + Num Input mode are toggled. Enter the number to be changed (1 through 128), then press [Enter]. When the number change is finished, the names of VIDEO and KEY are for the set number. Keys assigned number 121 through 128 can be used as the reentry buttons. When the SHIFT function is not used, Keys 121 through 124 are used, and when the SHIFT function is used, Keys 125 through 128 are used. Menu Operations 19 To return to the selection display of the Setup Menu Pressing [Ctrl]-[E] on each setting display. To return to the primary station menu Press [Ctrl]-[D]. Menu Item H: SET PHANTOM TABLE (for Router mode) Purposes Menu item H enables you to specify a phantom function to switch multiple crosspoints at a time using a source select button in RTR mode on the remote control unit. TAKE function and SHIFT function The TAKE function and SHIFT function are available in AUX mode as well. The settings are performed in menu item N. For details, see "Menu Item N: SET PANEL TABLE (for Router mode)" on page 23. Types and functions of phantom This control unit can use three phantom functions: "global phantom" registered in the primary station, "local phantom" registered in each control unit, and "destinationoffset local phantom" to use a substitute for destination selection. Global phantom The global phantom allows you to switch up to 2, 800 crosspoints by pressing a single button. This function may be used to switch crosspoints defined for a common phantom with two or more control units. Note The global phantom is set on the primary station, so the routing function does not work in synchronization with it. [. . . ] In the same manner as with menu item N, entry can be made either with its Type + Number name or description name. 32 Menu Operations Menu Item S: DISPLAY DESCRIPTION NAME Purposes Menu item S is available only when "J: NAME STYLE" is set to DESCRIP. NAME, and shows the description name list. To return to the selection display of the Setup Menu Press [Ctrl]-[E] on each setting display. To return to the primary station menu Press [Ctrl]-[D]. Calling the Menu item S display Press [S] on the selection display to select menu item S. Source list (example) SONY ROUTING SYSTEM SETUP MENU MKS-8082 V1. 00 SOURCE name Description name Description 0001 IN001 CAM001 0002 IN002 CAM002 0003 IN003 CAM003 0004 IN004 CAM004 0005 IN005 VTR005 0006 IN006 VTR006 0007 IN007 VTR007 0008 IN008 VTR008 0009 IN009 ONAIR01 0010 IN010 ONAIR02 0011 IN011 ONAIR03 0012 IN012 ONAIR04 0013 IN013 STADIO1 0014 IN014 STDIO2 0015 IN015 STADIO3 0016 IN016 STDIO4 0017 IN017 MONI001 0018 IN018 MONI002 0019 IN019 IN019 0020 IN020 IN020 0021 IN021 IN021 0022 IN022 IN022 0023 IN023 IN023 0024 IN024 IN024 0025 IN025 IN025 0026 IN026 IN026 0027 IN027 IN027 0028 IN028 IN028 0029 IN029 IN029 0030 IN030 IN030 0031 IN031 IN031 0032 IN032 IN032 STATION NUMBER 6 Ctrl-E : MENU Ctrl-D : RETURN Right : DESTINATION Left : SOURCE Destination list (example) SONY ROUTING SYSTEM SETUP MENU MKS-8082 V1. 00 DESTINATION name Description name Description 0001 OUT001 DST001 0002 OUT002 DST002 0003 OUT003 DST003 0004 OUT004 DST004 0005 OUT005 DST005 0006 OUT006 DST006 0007 OUT007 DST007 0008 OUT008 DST008 0009 OUT009 OUT009 0010 OUT010 OUT010 0011 OUT011 OUT011 0012 OUT012 OUT012 0013 OUT013 OUT013 0014 OUT014 OUT014 0015 OUT015 OUT015 0016 OUT016 OUT016 0017 OUT017 OUT017 0018 OUT018 OUT018 0019 OUT019 OUT019 0020 OUT020 OUT020 0021 OUT021 OUT021 0022 OUT022 OUT022 0023 OUT023 OUT023 0024 OUT024 OUT024 0025 OUT025 OUT025 0026 OUT026 OUT026 0027 OUT027 OUT027 0028 OUT028 OUT028 0029 OUT029 OUT029 0030 OUT030 OUT030 0031 OUT031 OUT031 0032 OUT032 OUT032 STATION NUMBER 6 Ctrl-E : MENU Ctrl-D : RETURN Right : DESTINATION Left : SOURCE Menu Operations 33 Error Messages When trouble occurs with this unit, the following error messages appear in the display window. The displayed message will automatically disappear after a few seconds. [. . . ]