User manual SONY MKS8160M

[. . . ] SWITCHER PROCESSOR PACK MVS8000SF-C MULTI FORMAT SWITCHER PROCESSOR MVS-8000SF HK-PSU04 MKS-8110HD MKS-8160HD MKS-8170HD MKS-8210HD MKS-8440HD MKS-8210K1 MKS-8110SD MKS-8160SD MKS-8170SD MKS-8210SD MKS-8440SD MKS-8440K1 MKS-8110M MKS-8160M MKS-8170M MKS-8210M MKS-8440M MKS-8420M INSTALLATION MANUAL 1st Edition (Revised 2) !WARNING This manual is intended for qualified service personnel only. To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so. Refer all servicing to qualified service personnel. ! [. . . ] If this LED does not light, the fuse may have blown. D2 (A-4) : +3. 3 V +3. 3 V power supply status indication. D3 (A-4) : +2. 5 V +2. 5 V power supply status indication. D5 (A-5) : CONF1 status LED H2 to L2 FPGA (Spartan II) CONFIG DONE status indication. Not lit when configuration is completed. D6 (A-5) : CONF2 status LED D10 to L10 FPGA (Spartan II) CONFIG DONE status indication. Not lit when configuration is completed. <Switch> S1 (A-6) : DI reset switch Pressing this switch initializes the DI-40 and D-I41 boards. <Connector> CN1 (A-6) : ISP common connector Used only for production in the assembly factory. Used for program writing into the JTAG device with ISP. <TEST terminal> E1 (C-6), E2 (J-2), E3 (P-5), E4 (B-11), E5 (H-11), E6 (N-8), E7 (A-7) : GND terminal bard Use this terminal as the earth point for measuring the respective check terminals. MVS-8000SF 1-28 1-8. Checks on Completion of Installation E1 (A-4), E2 (J-2), E3 (F-6), E4 (D-11), E5 (H-11), E6 (N-8), E7 (L-12) : GND terminal (DI-41 board) Use this terminal as the earth point for measuring the respective check terminals. TP1 (A-4) : +3. 3 V check terminal +3. 3 V measuring terminal. TP2 (A-4) : +2. 5 V check terminal +2. 5 V measuring terminal. TP3 (A-3) : +12 V check terminal +12 V measuring terminal. TP201 (N-13) : VD (vertical sync) signal check terminal VD signal measuring terminal. TP202 (N-13) : CKX (control timing) signal check terminal CKX signal measuring terminal. TP203 (P-13) : HD (horizontal sync) signal check terminal HD signal measuring terminal. TP204 (P-13) : FLOE (field odd even) signal check terminal FLOE signal measuring terminal. TP1000 (D-8), TP1500 (E-8), TP2000 (A-8), TP2500 (B-8), TP3000 (D-5), TP3500 (E-4), TP4000 (H-5), TP4500 (K-5), TP5000 (L-5), TP5500 (N-5), TP6000 (L-8), TP6500 (K-8), TP7000 (G-8), TP7500 (H-8), TP8000 (G-4) : 1R001 signal check terminal (DI-40 board) 1R001 signal measuring terminal. TP1001 (D-8), TP1501 (E-8), TP2001 (A-8), TP2501 (B-8), TP3001 (D-5), TP3501 (E-4), TP4001 (H-5), TP4501 (K-5), TP5001 (L-5), TP5501 (N-5), TP6001 (L-8), TP6501 (K-8), TP7001 (G-8), TP7501 (H-8), TP8001 (G-4) : HANC signal check terminal (DI-40 board) HANC signal measuring terminal. TP1002 (D-8), TP1502 (E-8), TP2002 (A-8), TP2502 (B-8), TP3002 (D-5), TP3502 (E-4), TP4002 (H-5), TP4502 (K-5), TP5002 (L-5), TP5502 (N-5), TP6002 (L-8), TP6502 (K-8), TP7002 (G-8), TP7502 (H-8), TP8002 (G-4) : LINE signal check terminal (DI-40 board) LINE signal measuring terminal. TP1003 (D-8), TP1503 (E-8), TP2003 (A-8), TP2503 (B-8), TP3003 (D-5), TP3503 (E-4), TP4003 (H-5), TP4503 (K-5), TP5003 (L-5), TP5503 (N-5), TP6003 (L-8), TP6503 (K-8), TP7003 (G-8), TP7503 (H-8), TP8003 (G-4) : FRAME signal check terminal (DI-40 board) FRAME signal measuring terminal. TP1004 (D-8), TP1504 (E-8), TP2004 (A-8), TP2504 (B-8), TP3004 (D-5), TP3504 (E-4), TP4004 (H-5), TP4504 (K-5), TP5004 (L-5), TP5504 (N-5), TP6004 (L-8), TP6504 (K-8), TP7004 (G-8), TP7504 (H-8), TP8004 (G-4) : CRC signal check terminal (DI-40 board) CRC signal measuring terminal. [. . . ] YES NO Connect it correctly. Are the option boards installed into the specified slots?YES NO Install the option boards into the specified slots. (Refer to Section 1-4. ) The power supply unit is probably defective. NO Are the input and output cables connected correctly?YES Check connections of the input and output equipment. Is the Software installed correctly? [. . . ]