User manual SONY MSAC-FD2MA

[. . . ] If a fault should occur during operation of the unit, operate the disconnect device to switch the power supply off, or disconnect the power plug. WARNING: THIS WARNING IS APPLICABLE FOR USA ONLY. If used in USA, use the UL LISTED power cord specified below. Plug Cap Parallel blade with ground pin (NEMA 5-15P Configuration) Cord Type SJT, three 16 or 18 AWG wires Length Minimum 1. 5 m (4 ft . 11in. ), Less than 2. 5 m (8 ft . 3 in. ) Rating Minimum 10 A, 125 V Using this unit at a voltage other than 120V may require the use of a different line cord or attachment plug, or both. [. . . ] · When changing the setting: Press the v or V key to select the setting. Press the ENTER or B key to restore the previous screen. 3 Select an item. Use the v or V key to select the item, then press the B or ENTER key. The setting items are displayed in a popup menu, in a setting menu, in an adjustment menu or in the next menu window. 34 Using a MENU To clear the menu Press the MENU key. The menu disappears automatically if a key is not pressed for one minute. To reset items that have been adjusted Select the item that you want to reset, and press the RESET key on the Remote Commander. "Complete!" appears on the screen and the setting of the item that you have selected is reset to its factory preset value. Items that can be reset are: · "Contrast, " "Brightness, " "Color, " "Hue" and "Sharpness" on the "Adjust Picture. . . " menu of the Picture menu · "Dot Phase, " "H Size, " and "Shift" on the "Adjust Signal. . . " menu of the Signal menu · "Side Shot" on the Installation menu (VPL-CX125/CX155/CW125 only) Adjustments and Settings Using a Menu Storage of the settings The settings are automatically stored in the projector memory when the ENTER key is pressed. Note The resetting item of the Lamp timer setting is not memorized. If no signal is input If there is no input signal, "Cannot adjust this item. " appears on the screen. Unadjustable items Items that cannot be adjusted, depending on the input signal, are not displayed on the menu. For details, see page 45. Using a MENU 35 The Picture Menu The Picture menu is used for adjusting the picture or volume. Picture Signal Volume: Picture Mode: Adjust Picture Standard Adjust Picture Contrast: Brightness: Sharpness: Gamma Mode: Color Temp. : Standard 80 50 50 Graphics Low: Picture Signal Function Installation Setup Information 30 Function Installation Setup Information Sel: Set: Exit: Sel: Set: Back: Exit: Setting items Picture Mode Functions Initial setting Selects the picture mode. Standard · Dynamic: Emphasizes the contrast to produce a "dynamic" picture. · Standard: Normally select this setting. If the picture has roughness with the "Dynamic" setting, this setting reduces the roughness. For details, see page 57. Initial setting Set according to the input signal Adjustments and Settings Using a Menu H Size Set according to the input signal Shift Adjusts the position of the picture. H adjusts the Set according to horizontal position of the picture. V adjusts the vertical the input signal position of the picture. As the setting for H increases, the picture moves to the right, and as the setting decreases, the picture moves to the left. As the setting for V increases, the picture moves up, and as the setting decreases, the picture moves down. Use the b or the B key to adjust the horizontal position and the v and V key for the vertical position. You can set the aspect ratio of the picture to be displayed for the current input signal. This item is enabled only when an video signal (preset memory numbers 1 to 11) is input. · Full 2: The original image is projected fully in the window. · 4:3: Select to view a picture with normal 4:3 aspect ratio. · 16:9: Select to view a picture squeezed. Set according to the input signal Aspect (When the video signal is input) The Signal Menu 37 Setting items Aspect (When the PC signal is input) Functions Initial setting You can set the aspect ratio of the picture to be Set according to displayed for the current input signal. [. . . ] 37, 38 Auto Input Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Floor installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 Installing the projector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 IR Receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 L Lamp Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Lamp Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 Lamp Timer Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 LAMP/COVER indicators . . . . . . . . . . . . . . . . . . . . . . . 15 Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Location and function of controls Connector panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Rear/Side/Bottom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Top/Front/Side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 B Background . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Brightness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 C Cleaning the air filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]