User manual SONY MSAC-US70

[. . . ] Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. CAUTION You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment. 2-GB Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. [. . . ] Restart your computer when installation is completed, and then connect this unit to your computer. Use the following procedure to install the software. A part of the installation may take place automatically. Installing the device driver on your computer PNote Simultaneously with the installation of the device driver, the "Memory Stick Formatter" and the operating instructions (PDF file) are also installed on your computer. 1 Turn on your computer. At this point, do not connect this unit to your computer. To install the device driver when you are using Windows 2000 or Windows XP, you must log on with Administrator rights. 16-GB 2 3 4 5 6 7 8 Insert the supplied CD-ROM (MSAC-US40) into the CD-ROM drive on your computer. The Installer launcher starts up automatically. To install a driver, click the [Driver] button in the menu. Carefully read the License Agreement, and then click the [Agree] button. When you click the [Agree] button, installation of the driver starts. Click the [Next] button as prompted on the screen. When you click [Finish], the driver installation is completed. Following this, installation of the "Memory Stick Formatter" starts. Click the [Next] button as prompted on the screen. When you click [Finish], installation of "Memory Stick Formatter" is completed. To use "Memory Stick Formatter, " select [Start] ­ [Programs] ­ [Memory Stick Utility] ­ [Memory Stick Formatter]. Following this, installation of the operating instructions (PDF file) is performed automatically. When installation of the operating instructions is completed, the application selection screen returns. To end installation of the software at this point, click [Exit]. If you do so, "SonicStage" is not installed. To view the operating instructions, select [Start] ­ [Programs] ­ [Sony Memory Stick Reader Writer] ­ [MSAC-US40 Instructions]. PNote Adobe Reader from Adobe Systems Incorporated is required for viewing the operating instructions (PDF file). 17-GB Installing the "SonicStage" software on your computer 1 2 3 4 5 6 Do as follows to install "SonicStage. " Click the [SonicStage] button in the menu. Carefully read the License Agreement, and then click the [Yes] button. When you click the [Yes] button, installation of "SonicStage" starts. Click the [Next] button as prompted on the screen. Select the folder in which you want to install "SonicStage. " To change the folder suggested for the installation, click the [Browse] button and then select the folder. ­ When using Windows 2000/Windows XP ­ Log on as Administrator or using a user ID that has administrative privilege. 1 Double-click the "System" icon on the "Control Panel. " The "System Properties" screen appears. 2 Check if the device driver has already been installed. 1 Click the [Hardware] tab on the "System Properties" screen. 2 Click [Device Manager]. The "Device Manager" screen appears. 22-GB 2 (Continued) 3 Click [View]. 4 Click [View devices by type]. 5 Double-click [Other devices]. MSAC-US70] preceded by the "?" symbol is shown. 3 Delete the driver if installed. If you use the procedure described in Step 2 and confirm that [?MSAC-US40] is shown under "Other devices" in the "View devices by type" display, a separate device driver has already been installed. Use the following procedure to delete this driver. The "Confirm Device Removal" screen appears. 4 Restart your computer after disconnecting this unit from the computer. Install the device driver again by performing the procedure from Step 1 described on page 16. PNote If you delete other devices than [?MSAC-US40], your computer may no longer operate normally. 23-GB ­ When using Windows 98SE/Windows Me ­ 1 2 Double-click the "System" icon on the "Control Panel. " The "System Properties" screen appears. Check if the device driver has already been installed. 1 Click the [Device Manager] tab on the "System Properties" screen. MSAC-US40] preceded by the "?" symbol is shown. 3 Delete the driver if installed. If you use the procedure described in Step 2 and find that [?MSAC-US70] is shown under "Other devices, " a separate device driver has already been installed. [. . . ] t Install the driver from the supplied CD-ROM. (Page 16) ·No "Memory Stick" inserted. t Insert a "Memory Stick. " The "Memory Stick" cannot be accessed from Explorer or My Computer. The access lamp is not on ·Foreign matter adhering to the when a "Memory Stick" is connector section of the "Memory Stick. " inserted. t Check whether dust or dirt is adhering to the connector section of the "Memory Stick. " Remove any foreign matter and insert the "Memory Stick" again. [. . . ]