User manual SONY MSX-M1GSTEP

[. . . ] Do not expose batteries or apparatus with battery-installed to excessive heat such as sunshine, fire or the like. To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with the installation instructions. Indoor use only. This appliance is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT MARKING is located on the laser protective housing inside the enclosure. EMC and product safety is Sony Deutschland GmbH, Hedelfinger Strasse 61, 70327 Stuttgart, Germany. [. . . ] You can enjoy TV sound via the system by using just one HDMI cable. For details, see [Audio Return Channel] (page 62). 1 2 3 4 Press HOME. The home menu appears on the TV screen. Press C/c to select [Setup]. Press X/x to select [Audio Settings], then press . Press X/x to select [Auto Calibration], then press . The confirmation display for [Auto Calibration] appears. Operating the system via the TV remote (Remote Easy Control) You can control the basic functions of the system via the TV remote when the system's video output is displayed on the TV screen. For details, refer to the operating instructions of the TV. 51GB 5 Connect the calibration mic to the A. CAL MIC jack on the rear panel. Set up the calibration mic at ear level using a tripod, etc. The front of each speaker should face the calibration mic, and there should be no obstruction between the speakers and the calibration mic. back speakers (page 15), install the speakers in appropriate location and turn the surround amplifier on. To use the surround back speakers, set [Surround Back] in [Speaker Settings] to [Yes] (page 53) 8 Confirm the result of [Auto Calibration]. The conclusions appear on the TV screen. The first page shows the distance of the speakers. The second page shows the level of the speakers. Note L A. CA MIC C2 ECM-A · If measurement fails, follow the message then retry [Auto Calibration]. 9 Press X/x to select [OK] or [Cancel], then press . x The measurement is OK. Disconnect the calibration mic, then select [OK]. The result is implemented. Calibration mic x The measurement is not OK. Follow the message, then select [OK] to retry. Note 6 7 Press X/x to select [OK]. To cancel, select [Cancel]. Press . · While the Auto Calibration function works: ­ do not turn off the power. ­ do not disconnect the calibration mic. [Auto Calibration] starts. You can set the parameters from 0. 0 to 7. 0 meters. The numbers in the illustration indicate the following: 1Center speaker 2Front left speaker (L) 53GB x [Test Tone] The speakers will emit a test tone to adjust [Level]. [Off]: The test tone is not emitted from the speakers. [On]: The test tone is emitted from each speaker in sequence while adjusting level. When you select one of the [Speaker Settings] items, the test tone is emitted from each speaker in sequence. Adjust the sound level as follows. Using the Sleep Timer You can set the system to turn off at a preset time, so you can fall asleep listening to music. The time can be preset in intervals of 10 minutes. Press SLEEP. Each time you press SLEEP, the minutes display (the remaining time) changes by 10 minutes. When you set the sleep timer, "SLEEP" flashes in the front panel display. 1 2 3 4 5 6 7 8 9 Note Set [Test Tone] to [On]. Press X/x to select [Level], then press . Press X/x to select the desired speaker type, then press . Press C/c to select the left or right speaker, then press X/x to adjust the level. [. . . ] DTS-HD High Resolution Audio has a maximum transmission rate of 6 Mbps, with lossy compression. DTS-HD Master Audio The Movie mode is for use with stereo television shows and all programs encoded in Dolby Surround. The result is enhanced sound field directionality that approaches the quality of discrete 5. 1-channel sound. Dolby Surround Pro Logic DTS-HD Master Audio has a maximum transmission rate of 24. 5 Mbps, and uses lossless compression, and DTS-HD Master Audio corresponds to a maximum sampling frequency of 192 kHz, and maximum of 7. 1ch. HD Digital Cinema Sound (HD-D. C. S. ) As one method of decoding Dolby Surround, Dolby Surround Pro Logic produces four channels from 2 channel sound. Compared with the former Dolby Surround system, Dolby Surround Pro Logic reproduces left-to-right panning more naturally and localizes sounds more precisely. To take full advantage of Dolby Surround Pro Logic, you should have one pair of surround speakers and a center speaker. [. . . ]