User manual SONY MSX-M256A

[. . . ] Do not expose batteries or apparatus with battery-installed to excessive heat such as sunshine, fire or the like. To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with the installation instructions. Indoor use only. This appliance is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT MARKING is located on the laser protective housing inside the enclosure. Disposal of waste batteries (applicable in the European Union and other European countries with separate collection systems) This symbol on the battery or on the packaging indicates that the battery provided with this product shall not be treated as household waste. [. . . ] (Digital Cinema Auto Calibration) can set the appropriate surround sound automatically. Note Other Operations · The system outputs a loud test sound when [Auto Calibration] starts. Give consideration to children and neighbors. Receiving the digital audio signal of the TV (Audio Return Channel) The system can receive the digital audio signal of the TV via an HDMI cable when your TV is compatible with the Audio Return Channel function. You can enjoy TV sound via the system by using just one HDMI cable. For details, see [Audio Return Channel] (page 62). 1 2 3 4 Press HOME. The home menu appears on the TV screen. Press C/c to select [Setup]. Press X/x to select [Audio Settings], then press . Press X/x to select [Auto Calibration], then press . The confirmation display for [Auto Calibration] appears. Operating the system via the TV remote (Remote Easy Control) You can control the basic functions of the system via the TV remote when the system's video output is displayed on the TV screen. For details, refer to the operating instructions of the TV. 51GB 5 Connect the calibration mic to the A. CAL MIC jack on the rear panel. Set up the calibration mic at ear level using a tripod, etc. The front of each speaker should face the calibration mic, and there should be no obstruction between the speakers and the calibration mic. back speakers (page 15), install the speakers in appropriate location and turn the surround amplifier on. To use the surround back speakers, set [Surround Back] in [Speaker Settings] to [Yes] (page 53) 8 Confirm the result of [Auto Calibration]. The conclusions appear on the TV screen. The first page shows the distance of the speakers. The second page shows the level of the speakers. Note L A. CA MIC C2 ECM-A · If measurement fails, follow the message then retry [Auto Calibration]. 9 Press X/x to select [OK] or [Cancel], then press . x The measurement is OK. Disconnect the calibration mic, then select [OK]. [Surround Back Left/Right]* 0. 0 dB: Set the surround back speaker level. [Subwoofer] 0. 0 dB: Set the subwoofer level. * This item appears when you set it to [Yes] in the [Connection] setting. When you move the speakers, be sure to set the parameters of the distance (A) from the listening position to the speakers. You can set the parameters from 0. 0 to 7. 0 meters. The numbers in the illustration indicate the following: 1Center speaker 2Front left speaker (L) 53GB x [Test Tone] The speakers will emit a test tone to adjust [Level]. [Off]: The test tone is not emitted from the speakers. [On]: The test tone is emitted from each speaker in sequence while adjusting level. When you select one of the [Speaker Settings] items, the test tone is emitted from each speaker in sequence. Adjust the sound level as follows. Using the Sleep Timer You can set the system to turn off at a preset time, so you can fall asleep listening to music. The time can be preset in intervals of 10 minutes. Press SLEEP. Each time you press SLEEP, the minutes display (the remaining time) changes by 10 minutes. When you set the sleep timer, "SLEEP" flashes in the front panel display. 1 2 3 4 5 6 7 8 9 Note Set [Test Tone] to [On]. Press X/x to select [Level], then press . [. . . ] It supports a maximum sampling frequency of 96 kHz, and 7. 1 multichannel surround. DTS-HD High Resolution Audio has a maximum transmission rate of 6 Mbps, with lossy compression. DTS-HD Master Audio The Movie mode is for use with stereo television shows and all programs encoded in Dolby Surround. The result is enhanced sound field directionality that approaches the quality of discrete 5. 1-channel sound. Dolby Surround Pro Logic DTS-HD Master Audio has a maximum transmission rate of 24. 5 Mbps, and uses lossless compression, and DTS-HD Master Audio corresponds to a maximum sampling frequency of 192 kHz, and maximum of 7. 1ch. HD Digital Cinema Sound (HD-D. C. S. ) As one method of decoding Dolby Surround, Dolby Surround Pro Logic produces four channels from 2 channel sound. Compared with the former Dolby Surround system, Dolby Surround Pro Logic reproduces left-to-right panning more naturally and localizes sounds more precisely. [. . . ]