User manual SONY MV-S8000

[. . . ] SWITCHER PROCESSOR PACK MVS-8400 MVS-8300 MVS-8200 MULTI FORMAT SWITCHER PROCESSOR MVS-8000 HK-PSU04 MKS-8110HD MKS-8160HD MKS-8161HD MKS-8170HD MKS-8210HD MKS-8440HD MKS-8110SD MKS-8160SD MKS-8161SD MKS-8170SD MKS-8210SD MKS-8440SD INSTALLATION MANUAL 1st Edition !WARNING This manual is intended for qualified service personnel only. To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so. Refer all servicing to qualified service personnel. ! [. . . ] TP3717 (A-5) : +2. 5 V check terminal +2. 5 V measuring terminal. TP3723 (A-4) : +3. 3 V check terminal +3. 3 V measuring terminal. <LED on the CPU DR module> (C11) Refer to < LED on the CPU DR module > in "1. <Switch on the CPU DR module> (C11) Refer to < Switch on the CPU DR module > in "1. Checks on Completion of Installation 4. KPC-16 (MVS-8000) board A 1 B C D E F G TP6067 H J K L M N E6064 P R 2 TP6060 3 TP6061 4 E6069 TP6068 D6001 D6065 D6062 D6063 D6061 CN6000 E6066 5 D6060 6 7 E6063 TP6000 8 D6108 D6107 9 D6106 D6105 D6104 D6103 D6102 10 D6101 D6100 D6109 TP6802 E6065 TP6801 11 12 E6062 TP6800 13 TP6104 TP6103 TP6102 TP6101 A side/Component side <LED> D6001 (A-5) : RESET status LED System reset status indication. Lights on when the +3. 3 V power decreases. D6060 (A-5) : +3. 3 V +3. 3 V power supply status indication. Lights on when the +3. 3 V power is supplied. D6061 (A-6), D6062 (A-5), D6063 (A-5) : +1. 8 V +1. 8 V power supply status indication. Lights on when the +1. 8 V power is supplied. D6065 (A-5) : +12 V +12 V power supply status indication. Lights on when the +12 V power is supplied. If this LED does not light, fuse may have blown out. D6100 (A-10) : COMMON WASH FPGA CONFIG DONE status LED COMMON WASH FPGA CONFIG DONE status indication. Lights off when CONFIGuration is completed. D6101 (A-10) : WASH4 FPGA CONFIG DONE status LED WASH4 FPGA CONFIG DONE status indication. Lights off when CONFIGuration is completed. D6102 (A-10) : WASH3 FPGA CONFIG DONE status LED WASH3 FPGA CONFIG DONE status indication. Lights off when CONFIGuration is completed. 1-22 MVS-8400/8300/8200 IM 1-8. Checks on Completion of Installation D6103 (A-10) : WASH2 FPGA CONFIG DONE status LED WASH2 FPGA CONFIG DONE status indication. Lights off when CONFIGuration is completed. D6104 (A-9) : WASH1 FPGA CONFIG DONE status LED WASH1 FPGA CONFIG DONE status indication. [. . . ] YES NO Install the standard boards into the specified slots. (Refer to MVS-8000 Maintenance Manual. ) The power cord of the MVS -8000 is connected correctly?YES NO The option boards are installed into the specified slots? NO Install the option boards into the specified slots. (Refer to Section 1-4. ) Connect it correctly. YES The input and output cables NO are connected correctly? Check connections of the input and output equipment. The power supply unit is suspected as defective. YES Software is installed correctly? [. . . ]