User manual SONY MV-S8000SF

[. . . ] SWITCHER PROCESSOR PACK MVS8000SF-C MULTI FORMAT SWITCHER PROCESSOR MVS-8000SF HK-PSU04 MKS-8110HD MKS-8160HD MKS-8170HD MKS-8210HD MKS-8440HD MKS-8110SD MKS-8160SD MKS-8170SD MKS-8210SD MKS-8440SD INSTALLATION MANUAL 1st Edition !WARNING This manual is intended for qualified service personnel only. To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so. Refer all servicing to qualified service personnel. ! [. . . ] TP3602 (N-13) : HD (horizontal sync) signal check terminal Use this terminal to check the HD signal supplied from mother board. MVS-8000SF TP3603 (N-12) : CKX (control timing) signal check terminal Use this terminal to check the CKX signal supplied from mother board. TP3604 (N-12) : VD (vertical sync) signal check terminal Use this terminal to check the VD signal supplied from mother board. TP3605 (N-5) : Buffered VD0 (vertical sync) signal check terminal Use this terminal to check the VD signal that is used on this board. TP3606 (P-6) : Buffered CKX0 (switching) signal check terminal Use this terminal to check the CKX signal that is used in this circuit board. TP3607 (N-12) : CK (clock for video) signal check terminal Use this terminal to check the clock for video signal that is used in this circuit board. TP3610 (N-6) : Buffered HD0 (horizontal sync) signal check terminal Use this terminal to check the HD signal that is used in this circuit board TP3611 (N-7) : Buffered FLOE0 (field odd even) signal check terminal Use this terminal to check the FLOE signal that is used in this circuit board. TP3700 (A-4) : +12 V check terminal +12 V measuring terminal. TP3702 (A-5) : +1. 8 V check terminal +1. 8 V measuring terminal. TP3717 (A-5) : +2. 5 V check terminal +2. 5 V measuring terminal. TP3723 (A-4) : +3. 3 V check terminal +3. 3 V measuring terminal. <LED on the CPU DR module> (C11) Refer to < LED on the CPU DR module > in "1. <Switch on the CPU DR module> (C11) Refer to < Switch on the CPU DR module > in "1. Checks on Completion of Installation 4. KPC-16 board (MKS-8210HD/SD) A 1 B C D E F G TP6067 H J K L M N E6064 P R 2 TP6060 3 TP6061 4 E6069 TP6068 D6001 D6065 D6062 D6063 D6061 CN6000 E6066 5 D6060 6 7 E6063 TP6000 8 D6108 D6107 9 D6106 D6105 D6104 D6103 D6102 10 D6101 D6100 D6109 TP6802 E6065 TP6801 11 12 E6062 TP6800 13 TP6104 TP6103 TP6102 TP6101 A side/Component side <LED> D6001 (A-5) : RESET status LED System reset status indication. D6060 (A-5) : +3. 3 V +3. 3 V power supply status indication. D6061 (A-6), D6062 (A-5), D6063 (A-5) : +1. 8 V +1. 8 V power supply status indication. D6065 (A-5) : +12 V +12 V power supply status indication. If this LED does not light, the fuse may have blown. D6100 (A-10) : COMMON WASH FPGA CONFIG DONE status LED COMMON WASH FPGA CONFIG DONE status indication. Not lit when CONFIGuration is completed. D6101 (A-10) : WASH4 FPGA CONFIG DONE status LED WASH4 FPGA CONFIG DONE status indication. Not lit when CONFIGuration is completed. D6102 (A-10) : WASH3 FPGA CONFIG DONE status LED WASH3 FPGA CONFIG DONE status indication. [. . . ] YES NO Connect it correctly. Are the option boards installed into the specified slots?YES NO Install the option boards into the specified slots. (Refer to Section 1-4. ) The power supply unit is probably defective. NO Are the input and output cables connected correctly?YES Check connections of the input and output equipment. Is the Software installed correctly? [. . . ]