User manual SONY MZ-R700DPC

[. . . ] 3-223-666-12(1) Portable MiniDisc Recorder Operating Instructions MZ-R700/R700PC/R700DPC ©2000 Sony Corporation WARNING To prevent fire or shock hazard, do not expose the unit to rain or moisture. To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only. Do not install the appliance in a confined space, such as a bookcase or built-in cabinet. [. . . ] The recorder plays the MD digitally and sends analog signals to the externally connected equipment. RK-G136 (not supplied) Stereo mini-plug Portable DAT recorder, etc. to LINE IN Stereo system, etc. R (red) to i RK-G129 (not supplied) L (white) 2 phono plugs When the recorder is connected to an another audio component through the supplied remote control. When connecting a line cable (not supplied) to the headphones/ earphones jack of the remote control, be sure to set the "BEEP" setting to "BEEP OFF. " This keeps the beep sound out of the recorded signal or the output from the externally connected equipment. 1 2 Press ENTER, press <MENU, repeatedly until "BEEP" flashes in the display, and then press ENTER again. Press <MENU, repeatedly until "BEEP OFF" flashes in the display, and then press ENTER. To turn on the beep sound Select "BEEP ON" in step 2. 39 Notes · Even when connecting to the externally connected equipment, the Mega Bass function is operative. If you do not want the effect of the Mega Bass function on your recording or the output from the externally connected equipment, set "BASS" to "BASS OFF" (page 35). · When recording to an externally connected equipment, press VOL + repeatedly to raise the volume level to maximum, which is optimum for recording to an externally connected equipment. If, however, this level produces distortion in the recording, press VOL ­ several times to lower the level (to that shown in the illustration below). VOL + 40 Editing recorded tracks You can edit your recordings by adding/erasing track marks or labeling tracks and MDs. Premastered MDs cannot be edited. Notes on editing · Do not move or jog the recorder while "TOC Edit"* is flashing in the display. · You cannot edit tracks on an MD that is record-protected. Before editing tracks, close the tab on the side of the MD (page 54). · If you perform an editing operation while playing, be sure not to turn the power off until "TOC Edit" disappears in the display. · The lid does not open until "TOC Edit" disappears in the display after editing. TOC = Table of Contents When you operate the recorder with the supplied remote control, use the buttons and controls shown in parentheses. Erasing tracks T MARK <MENU, EDIT ENTER T MARK ENTER >/. To erase a track Note that once a recording has been erased, you cannot retrieve it. Make sure of the track you are erasing. 1 While playing the track you want to erase, press ENTER (EDIT for 2 seconds or more). continued 41 2 Press <MENU, (flip the lever towards > or . ) repeatedly until "EDIT" flashes in the display, and then press ENTER (ENTER) again. " : Name" flashes in the display, and the recorder plays the selected track repeatedly. Press <MENU, (flip the lever towards > or . ) repeatedly until " : Erase" flashes in the display, and then press ENTER (ENTER). "Erase OK?" and "PushENTER" appear alternately in the display. To cancel erasing, press T MARK (T MARK). The track is erased and the next track starts to play. All the tracks after the one erased are automatically renumbered. 3 4 To erase a part of a track Add track marks at the beginning and the end of the part you want to erase, then erase the part (page 43). To erase the whole disc You can quickly erase all the tracks and data of the MD at the same time. Note that once a recording has been erased, you cannot retrieve it. Be sure to check the contents of the disc you want to erase. 1 2 While the recorder is stopped, press ENTER (EDIT for 2 seconds or more). Press <MENU, (flip the lever towards > or . ) repeatedly until "EDIT" flashes in the display, and then press ENTER (ENTER) again. [. . . ] and Hong Kong model) 220 V AC, 50 Hz (Argentina model) 110/220 V AC, 60 Hz (Korean model) 100 - 240 V AC, 50/60 Hz (Other models) Nickel Cadmium rechargeable battery NC-WMAA (supplied) LR6 (size AA) alkaline battery (not supplied) Revolutions 350 rpm to 2, 800 rpm (CLV) Error correction ACIRC (Advanced Cross Interleave Reed Solomon Code) Sampling frequency 44. 1 kHz Sampling rate converter Input: 32 kHz/44. 1 kHz/48 kHz Coding ATRAC (Adaptive TRansform Acoustic Coding) ATRAC3 -- LP2 ATRAC3 -- LP4 Modulation system EFM (Eight to Fourteen Modulation) Number of channels 2 stereo channels 1 monaural channel Frequency response 20 to 20, 000 Hz ± 3 dB Battery operation time See "Battery life" (page 50) Wow and Flutter Below measurable limit 63 Approx. 81 × 28. 1 × 74. 4 mm (w/h/ d) (31/4 × 11/8 × 3 in. ) without projections. Dimensions Mass Approx. 116 g (4. 1 oz) the recorder only Supplied accessories AC power adaptor (1) Headphones/earphones with a remote control (1) Optical cable (1) NC-WMAA Nickel Cadmium rechargeable battery (1) Rechargeable battery carrying case (1) Carrying pouch/Carrying case with a belt clip (except U. S. A. model) (1) US and foreign patents licensed from Dolby Laboratories. [. . . ]