User manual SONY NEW J OPERATING MANUAL

[. . . ] COMPACT PLAYER J-10 J-10SDI J-30 J-30SDI (J-30/30SDI) (J-30/30SDI) OPERATION MANUAL 1st Edition [English] WARNING To prevent fire or shock hazard, do not expose the unit to rain or moisture. To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only. · Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. [. . . ] · This unit uses an auto-tracking function (when using the Digital Betacam or MPEG IMX format). The factory setting for the auto-tracking is on (AUTO TRACKING ON). For details on how to change the setting, contact your nearest Sony dealer. While this unit is pulling the tape in, the PLAY button indicator B flashes. When using the Dolby C NR system When using an analog Betacam cassette, you can use Dolby C NR for audio playback. To activate the Dolby NR system, press the AU MON SEL/DOLBY C NR button while holding down the SHIFT button on the control panel. Insert a cassette beforehand. For details of how to insert a cassette, see the section "Inserting and ejecting cassettes" on page 3-2. To start playback Press the PLAY button. To stop playback Press the STOP button. Chapter 4 Playback 4-1 4-1 Playback Procedures 4-1-2 Playback in Jog Mode 4-1-3 Playback in Shuttle Mode 1 1 Chapter 4 Playback 1, 2, 3 In jog mode, the JOG dial controls the playback speed based the speed at which the dial is turned. The playback speed range is ±1 times normal speed. Use the following procedure to carry out playback in jog mode. 3 1, 2, 3 1 Turn the JOG dial directly or press the JOG/ SHUTTLE button to light the JOG indicator. Pressing the JOG/SHUTTLE button toggles between jog mode and shuttle mode. In shuttle mode, the SHUTTLE dial controls the playback speed based on the angular position of the dial. · When using a Digital Betacam tape: ±21 times · When using an MPEG IMX tape: ±32 times/±38 times (NTSC/PAL) · When using a Betacam SX tape: ±35 times · When using an analog Betacam tape: ±18/±20 times (NTSC/PAL) + indicates forward direction speed, ­ indicates reverse direction speed. The SHUTTLE dial has detents at the center position, move the SHUTTLE dial to the center indent to display a still picture. Use the following procedure to carry out playback in shuttle mode. 2 Turn the JOG dial in the desired direction, at a speed corresponding to the desired playback speed. Playback in jog mode starts. 3 To stop playback in jog mode, stop turning the JOG dial. It is possible to make pressing the JOG/SHUTTLE button to switching between JOG and SHUTTLE mode. Select "KEY" in SELECTION FOR JOG/ SHUTTLE DIAL ENABLE, extended menu item 101, to enable the above feature. (This is the default setting. ) 1 Turn the SHUTTLE dial directly or press the JOG/ SHUTTLE button twice to light the SHTL indicator. If the SHUTTLE dial points to a position other than the center, playback in shuttle mode starts at a speed corresponding to the angular position of the dial. Pressing the JOG/SHUTTLE button toggles between jog mode and shuttle mode. 4-2 Chapter 4 Playback 2 Turn the SHUTTLE dial to the angle corresponding to the desired playback speed. Playback in shuttle mode starts. 4-1-4 Noiseless Playback Function and Frame Step Playback Function When you are using the Betacam SX or MPEG IMX format, you can put this unit into noiseless mode for noiseless jog and shuttle playback at up to ±0. 5 times normal speed. During noiseless playback, audio is muted for the MPEG IMX format. For the Betacam SX format, discontinuous audio in frame units is heard. [. . . ] Detected abnormal operation in a system control device, NV-RAM. Detected abnormal operation in a servo system device, NV-RAM. Detected abnormal operation in an RF system device, NV-RAM. Chapter 8 Maintenance and Inspection Chapter 8 Maintenance and Inspection 8-3 8-1 Removing a Cassette When Tape Slack Occurs 8-5 Digital Hours Meter The digital hours meter can display nine items of information, in corresponding display modes, about the operational history of the unit. Use it as a guide in scheduling periodic maintenance. [. . . ]