User manual SONY NSXDS15

[. . . ] Be sure to keep the Operating Instructions for future reference. All warnings and cautions in the Operating Instructions and on the unit should be strictly followed, as well as the safety suggestions below. Ventilation - The unit should be situated with adequate space around it so that proper heat ventilation is assured. Allow 10 cm clearance from the rear and the top of the unit, and 5 cm from the each side. [. . . ] "PRGM" disappears on the display. To add tracks to the program Repeat step 2 and 3 before starting playback. The tracks are added to the end of the program. To change the programed tracks Clear the program and reselect the tracks in your desired order. Notes on CDs 2 Press DISC DIRECT PLAY 1-3 to select a disc. Go to the next step when the tray stops rotating. 3 Press the numbered buttons on the remote control to program a track. The selected track number lights up on the display. -To select the 20th track, press +10, +10 and 0. -To select the 15th track, press +10 and 5. ·Do not place more than one disc on one tray. ·Do not tilt the unit with discs loaded. ·The unit may not play a CD-R/RW disc recorded on personal computers or certain kinds of CD-R/RW recorders. ·Do not attach adhesive label, etc. to either side of a CD-R/ RW disc, as doing so may cause malfunction. ·Do not load an unrecorded CD-R/RW disc. AM antenna: Rotate to find best reception. To switch to monaural FM reception Press MONO TUNER on the remote control. With each press, "MONO" and "STEREO" are displayed alternately on the display. Dynamic Integrated Neo Amplifier is a brand-new amplifier system where clear mid-to-high range frequency sound, as well as rich low frequency sound, can be reproduced and listeners can enjoy the close-to-original sound with less distortion at either high or low volume levels. En Tip: When FM stereo reception is poor, switching to monaural reduces noise. To switch the AM tuning interval Hold down TUNER/BAND and press POWER on the unit. With each press, the AM tuning interval alternates between 9 kHz/ step and 10 kHz/step. Tip: The default is 10 kHz/step. Change it only when using the unit in a 9 kHz/step area. Switching AM tuning interval clears all the preset stations. 13 TAPE OPERATIONS To play back type II (High position) tapes Turn MULTI JOG until "SOFT" is displayed while playing a type II tape. Then, the unit provides the optimum playback sound for type II tapes. En To eject the tape Press zPUSH EJECT after the deck stops completely. Notes on cassettes Playback Use only type I (normal) tapes. 1 Press TAPE/DECK 1/2 and insert the tape in either deck. Press zPUSH EJECT to open the cassette holder, and insert with the exposed side down and playback side facing out from the unit. Push zPUSH EJECT to close. To pause playback (DECK 2 only) Press a. To select a deck (DECK 1 or DECK 2) Press TAPE/DECK 1/2 (FUNCTION on the remote control) in stop mode when tapes are loaded in both decks. The deck number ("T1" or "T2") is displayed. To reset the tape counter Press s in stop mode, and the tape counter on the display is reset to "0000". Opening and closing the cassette holder will also reset the tape counter. [. . . ] ·Is the erasure prevention tab of the tape broken off?If so, cover the detection slot with adhesive tape. ·Is the lens affected by condensation?If so, wait approximately one hour and try again. En Condensation Moisture may form on the CD pickup lens when: ·The unit is moved from a cold spot to a warm spot ·The heating system has just been turned on ·The unit is used in a very humid room ·The unit is cooled by an air conditioner When this unit has condensation inside, it may not function normally. [. . . ]