User manual SONY NSZ-GT1 DATASHEET

[. . . ] Windows 2000 is an abbreviation for Microsoft® Windows® 2000 Professional, Microsoft® Windows® 2000 Server, and Microsoft® Windows® 2000 Advanced Server. Windows XP is an abbreviation for Microsoft® Windows® XP Professional and Microsoft® Windows® XP Home Edition. Windows Server 2003 is an abbreviation for Microsoft® Windows ServerTM 2003 Standard Edition, Microsoft® Windows ServerTM 2003 Enterprise Edition, Microsoft® Windows ServerTM 2003 Datacenter Edition, and Microsoft® Windows ServerTM 2003 Web Edition. All names used in the sample applications are fictitious. [. . . ] · Only use these screws when installing the brackets. They are metric screws (length: 5. 0 mm; length below washer: 4. 0 mm). Using longer screws could result in damage. 4. 0 mm metric screw Built-in AIT 19 To install the brackets Align the Built-In AIT screw holes with the far end of the bracket adjustable screw holes. With a Phillips screwdriver, tighten the screws. 20 Built-in AIT Setting the Built-In AIT - Setting with the jumper pins You can change the following settings with the jumper pins on the rear of the Built-In AIT. · SCSI ID (factory-set to "ID4") · Parity function (factory-set to "Enabled") SCSI ID (pin 0 to 3 from right) Unused (NC) Parity (PD) Hint "Without jumper plug" means that one jumper plug is attached to one of the two pins, or that the jumper plug has been removed altogether. If you remove the jumper plug, make sure you store it in a safe place. Hint "With jumper plug" means a status that the jumper plugs are attached to two pins. "Without jumper plug" means a status that no jumper plug is attached to either pin or it is attached to one of two pins. Built-in AIT 21 Setting SCSI ID Set SCSI ID which is used by the Built-In AIT. Use four jumper pins, pin 0 to pin 3, on the rear of the Built-In AIT. Pin 3 (Factory-set to "Without jumper plug") Pin 2 (Factory-set to "With jumper plug") Pin 1 (Factory-set to "Without jumper plug") Pin 0 (Factory-set to "Without jumper plug") Important Check that the Built-In AIT's SCSI ID is not duplicated with SCSI ID of other SCSI device. SCSI ID 0 1 2 3 4*1 5 6 7*2 8 9 10 11 12 13 14 15 Pin 3 Pin 2 Pin 1 Pin0 : With jumper plug : Without jumper plug *1 : Factory-set value *2 : Do not set SCSI ID to ID7. 22 Built-in AIT Setting the parity function Set the parity function using the leftmost jumper pin on the rear of the Built-In AIT. The parity function is "Enabled" when setting "Without jumper plug" (factory-set value). The parity function is "Disabled" when setting "With jumper plug". PD (Factory-set to "Without jumper plug") Important For better reliability, use with "Enabled (Without jumper plug)". Setting the Built-In AIT - Setting with the DIP switch The DIP switch on the bottom of the Built-In AIT enables you to change the following settings. · Terminator Power (Terminator power supply) (Factory-set to OFF) · DC Control (1) (Data compression setting) (Factory-set to ON) · DC Control (2) (Data compression setting) (Factory-set to OFF) ON 12345678 Switches 1 to 4: Unused Switch 5: Terminator Power Switch 6: Unused Switch 7: DC Control (1) Switch 8: DC Control (2) Built-in AIT 23 Setting terminator power - Terminator Power Set whether terminator power is supplied to the SCSI bus or not. Make sure this ID is not used by any other device in the system. · This unit does not have a built-in terminator. When connecting this unit to the last terminal of the SCSI bus terminal, attach a terminator to the end of the SCSI cable. 26 Built-in AIT 3 Attach the cover to the basic processing unit. 5 When the SCSI bus can be set on the side of the basic processing unit, set the following on the Built-In AIT. · Transfer rate : 160 Mbyte/second (max. , synchronous) · Data bus width : 16 bits (Ultra Wide SCSI, LVD/SE) · DISCONNECT/RECONNECT function : Enable This device has a maximum transfer rate of 160 Mbyte/second. Set the transfer rate to 160 Mbyte/second on Built-In AIT units that support it, and to the next greatest transfer rate under 160 Mbyte/second on those that do not. When using the N8103-75F SCSI board, set to 160 Mbyte/second. Also, when the N8141-28AF expansion unit is connected, even if the transfer rate of the Built-In AIT is 160 Mbyte/second, set it to the next greatest transfer rate under 160 Mbyte/second. For details, see the instruction manual provided with the basic processing unit. Important Set the maximum transfer rates as follows according to the number of devices connected to the bus and the SCSI cable length. If you have other specifications at your disposal, use them over the ones below. SCSI ID Maximum transfer rate (Mbyte/s) Data bus width (bit) Maximum cable Maximum number length (m) of devices Single-ended Ultra 160 SCSI Ultra 2 Wide SCSI Ultra Wide SCSI Ultra Wide SCSI Ultra Wide SCSI Fast Wide SCSI Wide SCSI 160 80 40 40 40 20 10 16 16 16 16 16 16 16 4 3 1. 5 3 6 LVD* 12 12 3 3 3 (SCSI host + number of devices) 16 16 4 8 16 16 8 * When the SCSI host and all devices connected to the same bus are LVD-compatible. Built-in AIT 27 Installing the tape device driver Only install the device drive if you intend to use Windows 2000 Backup, Windows XP Backup, or Windows Server 2003 Backup (found in their respective System Tools folder). [. . . ] (An LED is flashing and an error is displayed on the LCD. ) Internal/ External Internal External Action Refer to the explanation of the LED and LCD indicators (if any) in the User's Guide. · If a cleaning request is indicated, clean the drive and attempt the backup process again. If the same error occurs again, replace the data cartridge. · If an error is indicated (ERRxx, for example), there may be a problem with the drive. [. . . ]