User manual SONY VAIO PCGA-UMS3 DATASHEET

[. . . ] Be sure to insulate any loose unconnected wires with electrical tape for safety. notes on the power supply cord (yellow) · When connecting this unit in combination with other stereo components, the connected car circuit's rating must be higher than the sum of each component's fuse. When no car circuits are rated high enough, connect the unit directly to the battery. Front speaker Frontlautsprecher Haut-parleur avant Diffusori anteriori Voorluidspreker Rear speaker Hecklautsprecher Haut-parleur arrière Diffusori posteriori Achterluidspreker Power amplifier Endverstärker Amplificateur de puissance Amplificatore di potenza Eindversterker MD/CD changer MD/CD-Wechsler Changeur de MD/CD Cambia MD/CD MD/CD-wisselaar Rotary commander RM-X4S Joystick RM-X4S Satellite de commande RM-X4S Telecomando a rotazione RM-X4S Bedieningssatelliet RM-X4S The numbers in the list are keyed to those in the instructions. [. . . ] The bracket 1 and the protection collar 4 are attached to the unit before shipping. Before mounting the unit, use the release keys 7 to remove the bracket 1 and the protection collar 4 from the unit. Keep the release keys 7 for the future use as they are also necessary if you remove the unit from your car. Handle the bracket 1 carefully to avoid injuring your fingers. 1 Catch Note Before installing, make sure that the catches on both sides of the bracket 1 are bent inwards 2 mm. If the catches are straight or bent outwards, the unit will not be installed securely and may spring out. Be sure to connect the earth cord before connecting the amplifier. If you connect an optional power amplifier and do not use the built-in amplifier, the beep sound will be deactivated. Tip (2-B- ) For connecting two or more MD/CD changers, the source selector XAC30 (optional) is necessary. Connecting any other system may damage the unit. If you have any questions and problems connecting your unit that are not covered in this manual, please consult the car dealer. Choose the installation location carefully so that the unit will not interfere with normal driving operations. Avoid installing the unit in areas subject to dust, dirt, excessive vibration, or high temperature, such as in direct sunlight or near heater ducts. Use only the supplied mounting hardware for a safe and secure installation. Before installing the unit, remove the protection collar 4 and the bracket 1 from the unit. Yellow Gelb Jaune Giallo Geel Yellow Gelb Jaune Giallo Geel continuous power supply permanente Stromversorgung alimentation continue alimentazione continua continu voeding Red Rot Rouge Rosso Rood Yellow Gelb Jaune Giallo Geel switched power supply geschaltete Stromversorgung alimentation commutée alimentazione commutata geschakelde voeding 1 Engage the release keys 7 together with the protection collar 4. 2 Pull out the release keys 7 to remove the protection collar 4. 1 Insert both release keys 7 together between the unit and the bracket 1 until they click. 2 Pull down the bracket 1, then pull up the unit to separate. Bend these claws outward for a tight fit, if necessary (5-2). [. . . ] 2 Pull down the bracket 1, then pull up the unit to separate. Bend these claws outward for a tight fit, if necessary (5-2). Make sure that the 4 catches on the protection collar 4 are properly engaged in the slots of the unit (5-3). Yellow Gelb Jaune Giallo Geel Yellow Gelb Jaune Giallo Geel switched power supply geschaltete Stromversorgung alimentation commutée alimentazione commutata geschakelde voeding Red Rot Rouge Rosso Rood Yellow Gelb Jaune Giallo Geel continuous power supply permanente Stromversorgung alimentation continue alimentazione continua continu voeding How to detach and attach the front panel (6) Before installing the unit, detach the front panel. [. . . ]