User manual SONY PCV-A15XD2

[. . . ] CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Discard used batteries according to the manufacturer's instructions. CAUTION: The battery pack used in this device may present a fire or chemical burn hazard if mistreated. [. . . ] Block Diagram ····························································· 4-1 5. Connector List ······························································ 5-1 5-2. Frame Harness Diagram ·············································· 5-2 6. Exploded View And Parts List ····································· 6-1 6-2. Parts List (Accessories and Packing Materials) ··········· 6-2 Confidential --3-- PCVA-15XD2 (UC) Identifying parts and controls This switch turns the display on and off. The indicator lights up in green when the display is turned on. The indicator lights up in orange when the display is in power saving mode. 2 2 +/­ Brightness control This control adjusts the brightness of the screen. 3 DVI video input connector (page 9) This connector inputs digital RGB video signals. 1 1 Power switch and indicator (pages 10, 12) See the pages in parentheses for further details. Right Pin No. Signal TMDS Data 2­ TDMS Data 2+ TDMS Data 2 Shield DDC Clock DDC Data TDMS Data 1­ TDMS Data 1+ TDMS Data 1 Shield 1 2 3 6 7 9 10 11 Pin No. 14 15 16 17 18 19 22 23 24 Signal +5V Power Ground (for +5V) Hot Plug Detect TDMS Data 0­ TDMS Data 0+ TDMS Data 0 Shield TDMS Clock Shield TDMS Clock+ TDMS Clock­ SECTION 1 OVERVIEW Left 1-1 (END) 4 DC IN connector (page 10) This connector provides DC power to the display. Connect the AC adapter to this connector. US (Continued) This section is extracted from instruction manual (4-649-778-01). Confidential PCVA-15XD2 (UC) 7 8 SECTION 2 DISASSEMBLY 2-1. FLOWCHART ARM REAR COVER P2-1 ARM FRONT COVER P2-2 REAR COVER P2-3 INVERTER UNIT P2-3 LCD ASS'Y (S) P2-4 LEX-23 BOARD P2-4 IFX-105 BOARD P2-5 · P X-X means pages that appears in this manual. 2-2. ARM REAR COVER 4 Three claws 4 Five claws 4 Five claws 5 VAIO rear cover 1 Slant the LCD ass'y (S) in the direction of arrow A. A 3 Arm rear cover 2 Four claws 6 Four screws +PS (3 × 5) Confidential 2-1 PCVA-15XD2 (UC) 2-3. ARM FRONT COVER Base cover upper 7 Tie band DVI cable, Power cable 8 Remove the DVI cable and the power cable from the tie band. 6 Seven screws +BVTP (3 × 8) q; Pull out the DVI cable and give the DVI cable a play. 3 Raise the arm plate ass'y. 9 Pull out the power cable. 5 Arm front cover 1 Seven claws 4 Four claws 2 Base cover lower Confidential PCVA-15XD2 (UC) 2-2 2-4. REAR COVER, INVERTER UNIT 1 Four screw covers 2 Four screws +B (3 × 16) 5 Three screws +P (3 × 3) 4 Rear cover 6 Shield cover INV 7 Three screws +P (3 × 4) 9 Harness (LCD 2P) qa Inverter cable (2P) q; Harness (LCD 2P) 8 Cover ass'y qs Inverter unit 3 Ten claws (Front cover ass'y) Confidential 2-3 PCVA-15XD2 (UC) 2-5. LCD ASS'Y (S), LEX-23 BOARD 1 Front cover ass'y 4 LCD ass'y (S) 2 LCD cable (A) Plastic tape 6 VR-SW cable (6P) 3 LCD cable (B) 5 Two screws +P (2 × 3) 7 LEX-23 board Confidential PCVA-15XD2 (UC) 2-4 2-6. IFX-105 BOARD 1 Four screws +P (3 × 3) 7 Four screws +P (3 × 3) 9 IFX-105 board 3 Shield cover IFX 8 DVI cable (2P) 4 Inverter cable (2P) 5 VR-SW cable (6P) 2 Two claws 6 Power cable (17P) 2-7. MAIN ELECTRICAL PARTS LOCATION DIAGRAM IFX-105 board LCD ass'y (S) Inverter unit LEX-23 board Confidential 2-5 (END) PCVA-15XD2 (UC) SECTION 3 SERVICE OVERVIEW 3-1. Name Parts code Application 1 EDID writing tool J-2500-446-1 Used to connect the DVI cable and the PC during EDID writing of the PCVA-15XD2. 2 Firmware writing cable J-2500-447-1 Used to connect the pin-7 connector (CN2) on the IFX-105 mounted board during firmware writing of the PCVA-15XD2. Outside drawing 3-2. [. . . ] Some delay should be anticipated when ordering these items. The components identified by mark !Replace only with part number specified. Les composants identifiés par une marque !sont critiques pour la sécurité. [. . . ]